參數資料
型號： AD9957BSVZ
廠商： Analog Devices Inc
文件頁數： 51/64頁
文件大?。?/td> 0K
描述： IC DDS 1GSPS 14BIT IQ 100TQFP
產品培訓模塊： Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action
Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter
Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction
Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter
Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator
標準包裝： 1
分辨率（位）： 14 b
主 fclk： 1GHz
調節字寬（位）： 32 b
電源電壓： 1.8V, 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP 裸露焊盤
供應商設備封裝： 100-TQFP-EP（14x14）
包裝： 托盤
產品目錄頁面： 552 (CN2011-ZH PDF)
配用： AD9957/PCBZ-ND - BOARD EVAL AD9957 QUADRATURE MOD
Data Sheet
AD9957
Rev. C | Page 55 of 64
REGISTER BIT DESCRIPTIONS
The serial I/O port registers span an address range of 0 to 25
(0x00 to 0x19 in hexadecimal notation). This represents a total
of 26 registers. However, six of these registers are unused, yielding
a total of 20 available registers. The unused registers are 7, 8, 11
to 13, and 23 (0x07 to 0x08, 0x0B to 0x0D, and 0x17).
The number of bytes assigned to the registers varies. That is, the
registers are not of uniform depth; each contains the number
of bytes necessary for its particular function. Additionally, the
registers are assigned names according to their functionality.
In some cases, a register is given a mnemonic descriptor. For
example, the register at Serial Address 0x00 is named Control
Function Register 1 and is assigned the mnemonic CFR1.
The following section provides a detailed description of each bit
in the AD9957 register map. For cases in which a group of bits
serve a specific function, the entire group is considered as a
binary word and described in aggregate.
This section is organized in sequential order of the serial
addresses of the registers. Following each subheading are the
individual bit descriptions for that particular register. The
location of the bit(s) in the register are indicated by <A> or
<A:B>, where A and B are bit numbers. The notation, <A:B>,
specifies a range of bits from most significant to least significant
bit position. For example, <5:2> means bit positions 5 down to
2, inclusive, with Bit 0 identifying the LSB of the register.
Unless otherwise stated, programmed bits are not transferred to
their internal destinations until the assertion of an I/O update or
profile change.
Control Function Register 1 (CFR1)
Address 0x00, four bytes are assigned to this register.
Table 18. Bit Descriptions for CFR1 Register
Bit (s)
Mnemonic
Description
31
RAM Enable
0: disables RAM playback functionality (default).
1: enables RAM playback functionality.
30:29
Open
28
RAM Playback
Destination
Ineffective unless CFR1<31> = 1.
0: RAM playback data routed to baseband scaling multipliers (default).
1: RAM playback data routed to baseband I/Q data path.
27:26
Open
25:24
Operating Mode
00: quadrature modulation mode (default).
01: single tone mode.
1x: interpolating DAC mode.
23
Manual OSK
External Control
Ineffective unless CFR1<9:8> = 10b.
0: OSK pin inoperative (default).
1: OSK pin enabled for manual OSK control (see the Output Shift Keying (OSK) section).
22
Inverse Sinc Filter
Enable
0: inverse sinc filter bypassed (default).
1: inverse sinc filter active.
21
Clear CCI
This bit is automatically cleared by the serial I/O port controller. This operation requires several internal clock
cycles to complete, during which time the data supplied to the CCI input by the baseband signal chain is
ignored. The inputs are forced to all zeros to flush the CCI data path, after which the CCI accumulators are reset.
0: normal operation of the CCI filter (default).
1: initiates an asynchronous reset of the accumulators in the CCI filter.
20:17
Open
16
Select DDS Sine
Output
Ineffective unless CFR1<25:24> = 01b.
0: cosine output of the DDS is selected (default).
1: sine output of the DDS is selected.
15:14
Open
13
Autoclear Phase
Accumulator
0: normal operation of the DDS phase accumulator (default).
1: synchronously resets the DDS phase accumulator any time I/O_UPDATE is asserted or a profile
change occurs.
12
Open
11
Clear Phase
Accumulator
0: normal operation of the DDS phase accumulator (default).
1: asynchronous, static reset of the DDS phase accumulator.
10
Load ARR @ I/O
Update
0: normal operation of the OSK amplitude ramp rate timer (default).
1: OSK amplitude ramp rate timer reloaded any time I/O_UPDATE is asserted or a profile change occurs.
相關PDF資料
PDF描述
AD9956YCPZ IC SYNTHESIZER 1.8V 48LFCSP
S9S08DZ60F1MLH MCU 60K FLASH MASK AUTO 64-LQFP
AD9952YSVZ IC DDS 14BIT DAC 1.8V 48-TQFP
MC9S08DZ96MLF MCU 8BIT 96K FLASH 48-LQFP
AD5933YRSZ IC NTWK ANALYZER 12B 1MSP 16SSOP
相關代理商/技術參數
參數描述
AD9957BSVZ-REEL 功能描述:IC DDS 1GSPS 14BIT IQ 100TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD9957BSVZREEL13 制造商:AD 制造商全稱:Analog Devices 功能描述:1 GSPS Quadrature Digital Upconverter w/18-Bit IQ Data Path and 14-Bit DAC
AD9958 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel 500 MSPS DDS with 10-Bit DACs
AD9958 PCB 制造商:Analog Devices 功能描述:EVAL BOARD ((NS))
AD9958/PCB 制造商:Analog Devices 功能描述:Evaluation Board For 2-Channel 500 MSPS DDS With 10-Bit DACs 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:IC 10-BIT DAC DDS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*