- 您現在的位置：買賣IC網 > PDF目錄366235 > 62371AB (Intel Corp.) multi-function PCI device(多功能PCI設備) PDF資料下載
參數資料
| 型號： | 62371AB |
| 廠商： | Intel Corp. |
| 英文描述： | multi-function PCI device(多功能PCI設備) |
| 中文描述： | 多功能PCI設備（多功能的PCI設備） |
| 文件頁數： | 173/284頁 |
| 文件大小： | 1042K |
| 代理商： | 62371AB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁當前第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁
E
These are the command words which dynamically reprogram the Interrupt Controller to operate in various
interrupt modes. Any interrupt lines can be masked by writing an OCW1. A 1 written in any bit of this command
word will mask incoming interrupt requests on the corresponding IRQx line.
82371AB (PIIX4)
173
4/9/97 2:23 PM PIIX4aDS
INTEL CONFIDENTIAL
(until publication date)
PRELIMINARY
OCW2 is used to control the rotation of interrupt priorities when operating in the rotating priority mode and to
control the End of Interrupt (EOI) function of the controller. OCW3 is used to set up reads of the ISR and IRR, to
enable or disable the Special Mask Mode (SMM), and to set up the interrupt controller in polled interrupt mode.
The OCWs can be written into the Interrupt Controller any time after initialization.
8.6.2.
END-OF-INTERRUPT OPERATION
End of Interrupt (EOI)
The In Service (IS) bit can be set to 0 automatically following the trailing edge of the second INTA# pulse (when
AEOI bit in ICW1 is set to 1) or by a command word that must be issued to the Interrupt Controller before
returning from a service routine (EOI command). An EOI command must be issued twice with this cascaded
interrupt controller configuration, once for the master and once for the slave.
There are two forms of EOI commands: Specific and Non-Specific. When the Interrupt Controller is operated in
modes that preserve the fully nested structure, it can determine which IS bit to set to 0 on EOI. When a Non-
Specific EOI command is issued, the Interrupt Controller automatically sets to 0 the highest IS bit of those that
are set to 1, since in the fully nested mode the highest IS level was necessarily the last level acknowledged and
serviced. A Non-Specific EOI can be issued with OCW2 (EOI=1, SL=0, R=0).
When a mode is used that may disturb the fully nested structure, the Interrupt Controller may no longer be able
to determine the last level acknowledged. In this case a Specific End of Interrupt must be issued that includes as
part of the command the IS level to be reset. A specific EOI can be issued with OCW2 (EOI=1, SL=1, R=0, and
LO–L2 is the binary level of the IS bit to be set to 0).
Note that an IS bit that is masked by an IMR bit will not be cleared by a non-specific EOI if the Interrupt
Controller is in the Special Mask Mode.
Automatic End of Interrupt (AEOI) Mode
If AEOI=1 in ICW4, then the Interrupt Controller operates in AEOI mode continuously until reprogrammed by
ICW4. Note that reprogramming ICW4 implies that ICW1, ICW2, and ICW3 must be reprogrammed first, in
sequence. In this mode, the Interrupt Controller automatically performs a Non-Specific EOI operation at the
trailing edge of the last interrupt acknowledge pulse. Note that from a system standpoint, this mode should be
used only when a nested multi-level interrupt structure is not required within a single Interrupt Controller. The
AEOI mode can only be used in a master Interrupt Controller and not a slave (on CNTRL-1 but not CNTRL-2).
8.6.3.
MODES OF OPERATION
Fully Nested Mode
This mode is entered after initialization unless another mode is programmed. The interrupt requests are ordered
in priority from 0 through 7 (0 being the highest). When an interrupt is acknowledged, the highest priority request
is determined and its vector placed on the bus. Additionally, a bit of the Interrupt Service Register (IS[0:7]) is set.
This IS bit remains set until the microprocessor issues an End of Interrupt (EOI) command immediately before
returning from the service routine. Or, if the AEOI (Automatic End of Interrupt) bit is set, this IS bit remains set
until the trailing edge of the second INTA#. While the IS bit is set, all further interrupts of the same or lower
priority are inhibited, while higher levels will generate an interrupt (which will be acknowledged only if the
microprocessor internal interrupt enable flip-flop has been re-enabled through software).
相關PDF資料 |
PDF描述 |
|---|---|
| 6259 | CONNECTOR ACCESSORY |
| 6273 | 8-BIT LATCHED DMOS POWER DRIVER |
| 6275 | 8-BIT SERIAL-INPUT, CONSTANTCURRENT LATCHED LED DRIVER |
| 6276 | 16-BIT SERIAL-INPUT, CONSTANTCURRENT LATCHED LED DRIVER |
| 6277 | 8-BIT SERIAL-INPUT, CONSTANTCURRENT LATCHED LED DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 6237201015 | 制造商:Varta 功能描述:2/3 A Series Lithium 3 V 1350 mAh With Sleeve and Wire Cylindrical Battery |
| 6237201301 | 制造商:Varta 功能描述:BATTERY LITHIUM 2/3AA PCB 3V 制造商:Varta 功能描述:BATTERY, LITHIUM, 2/3AA, PCB, 3V 制造商:Varta 功能描述:2/3 AA Lithium 3 V 1350 mAh PCB Cylindrical Battery |
| 62372091322 | 制造商:3M Electronic Products Division 功能描述:HOT MELT ADHESIVELM Q 5/8"X8" 制造商:3M Electronic Products Division 功能描述:SCOTCH-WELD HOT MELT/LOW MELT 5KG 3762M |
| 62372093302 | 制造商:3M Electronic Products Division 功能描述:HOT MELT ADHESIVE |
| 62372098301 | 制造商:3M Electronic Products Division 功能描述:HOT MELT ADHESIVE |
發布緊急采購，3分鐘左右您將得到回復。