- 您現(xiàn)在的位置：買賣IC網 > PDF目錄370034 > 28222-13 (Conexant Systems, Inc.) ATM Transmitter/Receiver with UTOPIA Interface PDF資料下載
參數資料
| 型號： | 28222-13 |
| 廠商： | Conexant Systems, Inc. |
| 英文描述： | ATM Transmitter/Receiver with UTOPIA Interface |
| 中文描述： | 自動柜員機發(fā)射機/接收機的UTOPIA接口 |
| 文件頁數： | 69/161頁 |
| 文件大?。?/td> | 1832K |
| 代理商： | 28222-13 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
Errors in either the A1 or A2 PLCP framing octets cause an indication in the
LINE_STATUS register PLCP Frame Error bit and are counted. PLCP OOF
events are indicated by the PLCP OOF bit and counted. PLCP LOF events (OOF
for eight consecutive PLCP frames) are indicated by the PLCP LOF bit. If an
LOF condition persists for more than 2
–
3 seconds, the PLCP LOF 2
–
3 status bit
is set. This is determined by LOF being set for three consecutive rising edges of
the ONESECI input. Loss of cell delineation in 53-octet modes is indicated by the
LOC bit and counted. PLCP OOF and LOC indications also appear on the LOCD
output pin.
The PLCP Yellow Alarm status bit is set high after 10 consecutive frames with
a PLCP yellow alarm value of one and cleared after 10 consecutive frames of a
value of zero.
Errors detected in the receiver BIP-8 code checking circuit cause BIP-8 Error
to be set and counted. FEBE Error is set if any valid non-zero FEBE value (values
of 1 through 8) is received. This condition is also counted in the REM_BIP
counter. Invalid FEBE is set if any invalid FEBE value (9 through F) is received; a
value of F also causes FEBE All 1s to be set. This value is used to indicate that
the FEBE calculation is not supported at the far end of the circuit.
CN8223
2.0 Functional Description
ATM Transmitter/Receiver with UTOPIA Interface
2.6 ATM Cell Processing
100046C
Conexant
2-35
2.6.4 PLCP Cell Validation for Receive
In 57-octet PLCP formats, the PHY receiver implements framing state machines
for cell alignment as described in TR-TSV-000773. In 53-octet formats, the PHY
receiver implements the HEC alignment state machine as described in ITU I.432.
In serial framed 57-octet mode, the PHY receiver processes a serial stream to
find PLCP framing. Octet synchronization is provided externally in DS1 and E1
modes. Internal or external E3 octet synchronization and DS3 nibble
synchronization are provided to the PHY framer. Physical layer framing patterns
are automatically removed before recovery of the octet data. If unframed mode is
enabled, the receiver will search each bit position to determine octet alignment.
The 57-octet PLCP framing state machine contains three states: in-frame,
out-of-frame, and loss-of-frame. Valid framing is found when two consecutive
valid path overhead octets in sequence are observed after the A1, A2 framing
octets. The out-of-frame state is entered only from the in-frame state, when there
are errors in both the A1 and A2 octets or when there are two consecutive Pn
errors. This event is an OOF event, and is counted. The LOF state is entered after
eight consecutive PLCP frames in the out-of-frame state.
Stuffing and destuffing are provided according to the PHY type setting in
57-octet formats. Cycle stuffing is used at the transmit PLCP for DS3 and E3
whenever the receive PLCP is in the LOF state or the RCV_HLD input is high,
and this function is enabled with Receiver Hold Enable [bit 10] of CONFIG_1
[0x00]. Cycle stuffing can also be forced by setting Force Cycle Stuffing [bit 6]
of CONFIG_3 [0x02] high.
NOTE:
When the framing mode is dynamically modified between direct mapping
and PLCP framing, the CN8223 will go into an OOF state. Dynamic
switching should only be used if necessary.
2.6.4.1 PLCP Status
相關PDF資料 |
PDF描述 |
|---|---|
| 28222-14 | ATM Transmitter/Receiver with UTOPIA Interface |
| 28233-11 | ATM Transmitter/Receiver with UTOPIA Interface |
| 28C010TRPDB-12 | 150 x 32 pixel format, LED Backlight available |
| 28C010TRT1DE-15 | 1 Megabit (128K x 8-Bit) EEPROM |
| 28C010TRT1DE-20 | 1 Megabit (128K x 8-Bit) EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28222-14 | 制造商:CONEXANT 制造商全稱:CONEXANT 功能描述:ATM Transmitter/Receiver with UTOPIA Interface |
| 282222-003 | 制造商:TE Connectivity 功能描述:81044/12-16-2 - Cable Rools/Shrink Tubing |
| 282223-003 | 制造商:TE Connectivity 功能描述:81044/12-16-3 - Cable Rools/Shrink Tubing |
| 282224-003 | 制造商:TE Connectivity 功能描述:81044/12-16-4 - Cable Rools/Shrink Tubing |
| 282224-1 | 功能描述:汽車連接器 ECONOSEAL RCPT CONT .5MM RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
發(fā)布緊急采購，3分鐘左右您將得到回復。