參數資料
型號： STLC5411
廠商： 意法半導體
英文描述： 2B1Q U Interface Device(2BIQ U接口裝置)
中文描述： 2B1Q U接口設備（2BIQ ü接口裝置）
文件頁數： 14/72頁
文件大?。?/td> 738K
代理商： STLC5411
FUNCTIONAL DESCRIPTION
Digital Interfaces
STLC5411 provides a choice between two types
of digital interface for both control data and (2
B+D) basicaccessdata.
Theseare:
a) GeneralCircuit Interface:GCI.
b) Microwire/Digital System Interface:
μ
W/DSI
The device will automatically switch to one of
them by sensing the MW input pin at the Power
up.
μ
W/DSI MODE
Microwire control interface
The MICROWIRE interface is enabled when pin
MW equal one. Internalregisters can be written or
read through that control interface.
It is constitutedof 5 pins:
CI:
CO:
CCLK:
CS:
INT:
data in
data output
data clockinput
Chip Selectinput
Interruptoutput
Transmission of data onto CI & CO is enabled
when CS input is low.
A Write cycle or a Read cycle is always consti-
tuted of two bytes. CCLK must be pulsed 16
times while CS is low.
Transmission of data onto CI & CO is enabled fol-
lowing 2 modes.
– MODE A: the first CCLK edge after CS fall-
ing edge (and fifteen others odd CCLK
edges) are used to shift in the CI data, the
even edges being used to shift out the CO
data.
– MODE B: the CCLK first edge after CS falling
edge (and the fifteen others odd CCLK loss)
are used to shift out the CO data, the even
edges being usedto shiftin the CI data.
For each modes the first CCLK edge after CS fall-
ing edge can be positive or negative: the UID
automaticalydetects the CCLKpolarity.
Mode A is the default value. To select the mode
B, write MWPS register.
Youcan write in the UID on CI whilethe UID send
back a register content to the microprocessor. If
the UID has no messageto send, it forces the CO
output to all zero’s.
If the UID is to be read (status change has oc-
cured in the UID or a read-back cycle has been
requested by the controller), it pulls the INT out-
put low until CS is provided. INT high to low
transition is not allowed when CS is low (the UID
waits for CS high if a pending interrupt occurs
while CS is low) .
When CS is high, the CO pin is in the high imped-
ance state.
Write cycle
The format to write a 8 bits message into the UID
is:
A7
A6
A5
A4
1st byte
A3
A2
A1
A0
D7
D6
D5
D4
2nd byte
D3
D2
D1
D0
A7-A1:
A0:
D7-D0:
Register Address
Write/Readback Indicator
Register Content
After the first byte is shifted in, Register address
is decoded.A0 set low indicatesa write cycle: the
content of the following received byte has to be
loaded into the adressed register.
A0 set high indicates a read-back cycle request
and the byte following is not significant. The UID
will respond to the request with an interrupt cycle.
It is then possible for the microprocessor to re-
ceive the required register content after several
other pendinginterrupts.
To write a 12bits message, the differenceis:
limited addressfield:
extended data field (D11 - D8):A3 - A0.
The Write/Read back indicator doesn’t apply; to
read and write a 12 bits register two addresses
are necessary.
A7- A4
Read cycle
When UID has a register content to send to the
microprocessor, it pulls low the INT output to re-
quest CSand CCLK signals. Note that the data to
send can be the content of a Register previously
requested by the microprocessor by means of a
read-back request.
The formatof the 8 bits message sent by the UID
is:
A7
A6
A5
A4
1st byte
A3
A2
A1
A0
D7
D6
D5
D4
2nd byte
D3
D2
D1
D0
A7-A1:
A0:
D7-D0:
Register Address
forced to 1 if read back
forced to 0 if spontaneous
Register Content
STLC5411
14/72
相關PDF資料
PDF描述
STLC5412 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5412FN 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5412P 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5444 Quad Feed Power Supply(ISDN四饋電電源)
STLC5460 Line Card Interface Controller(線路卡片接口控制器)
相關代理商/技術參數
參數描述
STLC5411CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN Line Interface
STLC5411FN 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE
STLC5411P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE
STLC5412 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5412FN 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*