- 您現在的位置：買賣IC網 > PDF目錄380765 > STLC5411 (意法半導體) 2B1Q U Interface Device(2BIQ U接口裝置) PDF資料下載
參數資料
| 型號： | STLC5411 |
| 廠商： | 意法半導體 |
| 英文描述： | 2B1Q U Interface Device(2BIQ U接口裝置) |
| 中文描述： | 2B1Q U接口設備（2BIQ ü接口裝置） |
| 文件頁數： | 39/72頁 |
| 文件大?。?/td> | 738K |
| 代理商： | STLC5411 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
(H1), AR instruction forces UID through the ap-
propriate sequence to activate the line by sending
TN followed by SN1. Beeing in the U-only-active
state (H8A), AR command forces the sai bit equal
1 to the line. Is intended to transferto the network
an activation attempt at the S/T interface.
1011 (SP3):
Send SinglePulse +3 and -3
SP3 test command forces UID to send +3, -3
pulses to the line, one pulse per frame.
1100 (AI):
ActivationIndicate
AI command forces act bit equal one in SN3 sig-
nal transmitted to the line.Is intendedto reflect an
activatestate at the S/Tinterface.
1110 (AIL):
Activation IndicateLoopback
Identical to AI command. Ensure direct compati-
bility with status indicationsof SID-GCI.
1111 (DI):
DeactivationIndicate
The DI command allows the UID to automatically
enter the power down state if the line is deacti-
vated. DI command has no effect as long as the
line is not deactivated (DI status indication re-
ported).
NT mode: Status indication
0000 (DP/LSD):
Deactivation pending / Line sig-
nal detected
When in the deactivated state (H1) either pow-
ered up or down, LSD status indication is re-
ported if TN wake-up tone is detected except if
NT1 AUTO is selected; in this configuration, UID
must check uoa bit before to send (or not) LSD.
When in the superframe-synchronized states,DP
status indication reports that the dea bit has been
received equal zero from the line. UID enters in
the receive reset state.When NT1-AUTO mode is
selected, DP status indication is reported also
when a transmission error has been detected on
the loop. This is intended to ensure immediate
deactivationof the S/T interface.
0001 (EIU):
Error IndicationUser
EIU status indication is reported in following
cases:
a. to acknowledge RES command. UID is deacti-
vated,ready for a coldstart.
b. to report a Loss of signal for more then 480ms
on the line.
c. to report a Loss of synchronization for more
than480ms on the line. In this case, when NT-
RR-AUTO is selected, EIU is replaced by
RES;
d. to report that an expire of Timer 4 interrupt has
reset UID ready for a coldstart.
When NT1-AUTO is selected, EIU is replaced by
(DP) (except in case c.).
0100 (EI):
ErrorIndication
EI status indication reports that act bit has been
detected equal zero.
0110 (UAP):
U interfaceActivation pending
Is significant only when RR bit in CR2 has been
set equal one or if NT-RR-AUTO mode is se-
lected. UAP reports that the receiver is super-
frame synchronized with uoa bit received equal
zero.
1000 (AP):
Activation Pending
AP reports that the receiver is superframe syn-
chronized with uoabit received equal one .
1010 (ARL):
Activation RequestLoopback
Is significant only when NT1-AUTO or NT-RR-
AUTO mode is selected. ARL reports that an eoc
message has been received requiring to operate
a local 2B+D loopback. When connected to SID-
GCI in a NT1 or to UID in LT-RR-AUTO mode in
a regenerator,2B+D loopback command is there-
fore automaticallyprovided.
1100 (AI):
ActivationIndication
AI reports that UID is superframe synchronized
with act anduoa bits receivedequal one.
1111 (DI):
Deactivation Indication
DI reports that UID has entered the deactivated
state (H1).
LT mode: Command
0000 (PUP/DR):
Power Up / Deactivation Re-
quest When in the power down state, PUP com-
mand powers up the device ready for a cold or a
warm start. When in one of the superframe syn-
chronized states, DR command forces dea bit on
the line equal zero for four consecutive superfra-
mes beforeceasingtransmission.
0001 (RES):
Reset
RES command resets UID ready for a cold start.
Configurationregisters are not changed.REScan
be operatedwhen the device is either powered up
or down. If RES command is applied when the
line is not fully deactivated, UID returns EIU indi-
cation and goes in J1 state(Receive Reset).
If RES command is applied when the line is not
fully deactivated,UID properly ends the activation
before to come back in J1 state; in this case EIU
indicationis returned.
0010 (SP1):
Send SinglePulse +1 and-1
SP1 test command forces UID to send +1, -1,
pulses to the line,one pulse per frame.
0011 (RDT):
RandomData Transmitted
RDT test command forces UID to send data with
random equiprobablelevels at 80 kbaud.
0100 (FA0):
Forceact bit to Zero
FA0 command forces the act bit to 0 in the SL3
signal transmittedto the line. Is intended to reflect
a transmission failure detected on the network
side of the loop relative to UID.
STLC5411
39/72
相關PDF資料 |
PDF描述 |
|---|---|
| STLC5412 | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5412FN | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5412P | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5444 | Quad Feed Power Supply(ISDN四饋電電源) |
| STLC5460 | Line Card Interface Controller(線路卡片接口控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC5411CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ISDN Line Interface |
| STLC5411FN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE |
| STLC5411P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE |
| STLC5412 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5412FN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
發布緊急采購，3分鐘左右您將得到回復。