- 您現在的位置：買賣IC網 > PDF目錄381073 > SBPH400-3 (意法半導體) IEEE1394 3-Port 400Mbps Physical Layer PDF資料下載
參數資料
| 型號： | SBPH400-3 |
| 廠商： | 意法半導體 |
| 英文描述： | IEEE1394 3-Port 400Mbps Physical Layer |
| 中文描述： | IEEE1394連接3端口400Mbps的物理層 |
| 文件頁數： | 32/43頁 |
| 文件大?。?/td> | 285K |
| 代理商： | SBPH400-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
32/43
SBPH400-3
2.9.4 LKON (link on)
The LKON pin is used as an output to indicate that the SBPH400 has received a Link_On
packet. If the there is no signal on the LPS pin (indicating that the link device is not currently
powered) or the Link_active register is zero (link interface turned off by software) and a
Link_On packet is received addressed to the node, then a 6.144 MHz signal is output on the
LKON pin. This signal is turned off within 500 ns when both there is a signal received on LPS
and the Link_active register is 1.
2.10 ISO (isolation)
The SBPH400 supports the use of an isolation barrier between the chip and a link device. If
ISO is set high, then the an internal pulsed differentiating function is used on the CTL[0:1] and
the D[0:7] pins when used as outputs. Appropriate threshold circuitry is included on these pins
when used as inputs to interpret differentiated signals correctly. The differentiation circuitry
transmits a 1 or a 0 when there is a logical transition to 1 or 0 respectively, otherwise the output
is set to high impedance. This is shown in Table 2.22. This allows an arbitrary sequence of 1’s
or 0’s to be transmitted across an AC coupled isolation interface.
2.11 CPS (cable power status)
This input should be connected to the power supply provided from the cable via an external
series 400 KOhm resistor. Theinternal logic associated with thispin provides a nominal filtered
cable power failvoltage (as appliedto the external resistor) threshold of 6.25 volts. The internal
logic will report 1 in the PS register when the external voltage on the resistor exceeds the
threshold, and will report 0 in the PS register when the external voltage falls below the
threshold. A transition from 1 to 0 on the value in the PS register causes the Pwr_fail register
to be set to 1, which in turn will cause a link status transfer with the PHY_Interrupt bit set if the
Link interface is active, otherwise will cause a LinkOn signal. Appropriate protection is
incorporated in the SBPH400 for cable power voltages within the 1394 specification applied
via the external series resistor.
Table 2.22
Output differentiation for isolation
Next
0
1
Previous
0
1
Z
0
1
Z
2
相關PDF資料 |
PDF描述 |
|---|---|
| SD-B2D00 | CRYSTAL CLOCK OSCILLATORS |
| SD-BD00-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD01-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD07-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD09-FREQ | CRYSTAL CLOCK OSCILLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SBPSU10K15FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-15KVA 208V FLOO - Bulk |
| SBPSU10K15F-WP | 制造商:Schneider Electric 功能描述:APC MAINTENANCE BYPASS PANEL 10-15KVA 208V WALLMOUNT - Bulk |
| SBPSU10K20HC1M1-WP | 制造商:American Power Conversion Corp 功能描述:APC SMART-UPS VT MAINTENANCE B 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-20KVA 400V WALL - Bulk |
| SBPSU10K30FC1M1-WP | 制造商:Schneider Electric 功能描述:SMART-UPS VT BYPASS PANEL - Bulk 制造商:Schneider Electric 功能描述:APC Smart-UPS VT Maintenance Bypass Panel 10-30kVA 208V Wall Mount w/42 Pos. Dis |
| SBPSU20K30FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 20-30KVA 208V FLOO - Bulk |
發布緊急采購，3分鐘左右您將得到回復。