- 您現在的位置：買賣IC網 > PDF目錄381073 > SBPH400-3 (意法半導體) IEEE1394 3-Port 400Mbps Physical Layer PDF資料下載
參數資料
| 型號： | SBPH400-3 |
| 廠商： | 意法半導體 |
| 英文描述： | IEEE1394 3-Port 400Mbps Physical Layer |
| 中文描述： | IEEE1394連接3端口400Mbps的物理層 |
| 文件頁數： | 16/43頁 |
| 文件大?。?/td> | 285K |
| 代理商： | SBPH400-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
16/43
SBPH400-3
The SBPH400 has control over the bidirectional pins. It will, upon request, transfer this control
to the link device, which can then drive these pins. The 8 bidirectional data pins D[0:7] form
the data bus. The portion of the D bus which carries packet data is left-justified starting with
the 0 bit. Packet data for 100 Mb/s transfers uses D[0:1], 200 Mb/s transfers use D[0:3], and
400 Mb/s transfers use D[0:7]. The unused D[n] signals are transmitted as ‘0’ and are ignored
when the link device has control of the bus. The control bus CTL[0:1] carries the control
information. The LREQ pin is used by the link device to request access to the serial bus and
to read and write the chip registers.
2.8.2 Types of operation
The four basic operations which may occur at the PHY-Link interface are: request, status,
transmit and receive. Request is the only operation initiated by the link layer device. The link
layer device uses the request operation to read or write a register located in the SBPH400 or
to request the bus so that the SBPH400 can initiate a transmit action on the bus. The
SBPH400 initiates a receive action whenever a packet is received from the serial bus and a
status indication to notify events to the link layer device.
2.8.3 Control pins
When the SBPH400 has control of the PHY-Link interface the
CTL[0:1]
lines are encoded as
shown in Table 2.5.
When the link layer device has beengranted the PHY-Link interface bythe SBPH400, itshould
encode the
CTL[0:1]
lines Table 2.6
Table 2.5
CTL[0:1] When the SBPH400 is driving
CTL[0:1]
00
01
10
NAME
Idle
Status
Receive
DESCRIPTION
No activity (default mode)
The SBPH400 is sending status information to the link device
An incoming packet is being transferred from the SBPH400 to the link
device
The link device is granted the bus to send a packet
11
Grant
Table 2.6
CTL[0:1] when the link is driving (upon grant from SBPH400)
NAME
Idle
DESCRIPTION
The link device has released the bus (normally after transmission).
Note that multiple Idles may need to be transmitted.
The link device is preparing data or wishes to reacquire thebus without
arbitrating to send another packet
The link device is sending a packet to the SBPH400
00
01
Hold
10
11
Transmit
unused
2
相關PDF資料 |
PDF描述 |
|---|---|
| SD-B2D00 | CRYSTAL CLOCK OSCILLATORS |
| SD-BD00-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD01-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD07-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD09-FREQ | CRYSTAL CLOCK OSCILLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SBPSU10K15FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-15KVA 208V FLOO - Bulk |
| SBPSU10K15F-WP | 制造商:Schneider Electric 功能描述:APC MAINTENANCE BYPASS PANEL 10-15KVA 208V WALLMOUNT - Bulk |
| SBPSU10K20HC1M1-WP | 制造商:American Power Conversion Corp 功能描述:APC SMART-UPS VT MAINTENANCE B 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-20KVA 400V WALL - Bulk |
| SBPSU10K30FC1M1-WP | 制造商:Schneider Electric 功能描述:SMART-UPS VT BYPASS PANEL - Bulk 制造商:Schneider Electric 功能描述:APC Smart-UPS VT Maintenance Bypass Panel 10-30kVA 208V Wall Mount w/42 Pos. Dis |
| SBPSU20K30FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 20-30KVA 208V FLOO - Bulk |
發布緊急采購，3分鐘左右您將得到回復。