- 您現在的位置：買賣IC網 > PDF目錄381073 > SBPH400-3 (意法半導體) IEEE1394 3-Port 400Mbps Physical Layer PDF資料下載
參數資料
| 型號： | SBPH400-3 |
| 廠商： | 意法半導體 |
| 英文描述： | IEEE1394 3-Port 400Mbps Physical Layer |
| 中文描述： | IEEE1394連接3端口400Mbps的物理層 |
| 文件頁數： | 15/43頁 |
| 文件大?。?/td> | 285K |
| 代理商： | SBPH400-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
SBPH400-3
15/43
Figure 2.9
Remote confirmation packet format
The fields in the remote command and remote confirmation packets are interpreted as shown
in Table 2.4.
2.8
Link interface
2.8.1 Overview
The link interface in the SBPH400 operates as described in the IEEE P1394a proposal.
The SBPH400 implements an interface to a single 1394 link layer device, using the pins D[0:7],
Ctl[0:1], LREQ, SClk, LPS and LKON. The interface is scalable, using 2 data bits in parallel
per 100 Mbit/sec. This enables the clock rate of the signals at this interface to remain at 50
MHz.
Table 2.4
Remote Command and Confirmation packet fields
Field
phy_ID
Comment
Physical node identifier of the destination of the packet (type = 8)
Physical node identifier of the source of the packet (type = A
16
)
8 - remote command packet
A
16
- remote confirmation packet
Identify the port for the command or confirmation. For values other than 0, 1 and 2, the
SBPH400 always responds with the OK bit set to zero in the confirmation packet.
current value of the Fault bit from SBPH400 register 1001
2
for the addressed port
current value of the Connected bit from SBPH400 register 1000
2
for the addressed port
current value of the Bias bit from SBPH400 register 1000
2
for the addressed port
current value of the Disabled bit from SBPH400 register 1000
2
for the addressed port
1 if the immediately preceding remote command was accepted by the SBPH400, zero
otherwise
type = 8:-
0 - NOP
1 - Transmit TX_DISABLE_NOTIFY then disable the port
2 - Initiate suspend
4 - Clear the port’s Fault bit
5 - Enable port
6 - Resume port
type = A
16
:-
The cmnd value from the immediately preceding remote command packet
Current value of the SBPH400 register addressed by the immediately preceding Remote
Access packet (reserved and unimplemented fields and registers are returned as zero).
type
port
f
c
b
d
ok
cmnd
data
0 0
phy_ID
logical inverse of first quadlet
0
port
000
cmnd
0
000
type(A
16
)
f
c b d ok
2
相關PDF資料 |
PDF描述 |
|---|---|
| SD-B2D00 | CRYSTAL CLOCK OSCILLATORS |
| SD-BD00-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD01-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD07-FREQ | CRYSTAL CLOCK OSCILLATORS |
| SD-BD09-FREQ | CRYSTAL CLOCK OSCILLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SBPSU10K15FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-15KVA 208V FLOO - Bulk |
| SBPSU10K15F-WP | 制造商:Schneider Electric 功能描述:APC MAINTENANCE BYPASS PANEL 10-15KVA 208V WALLMOUNT - Bulk |
| SBPSU10K20HC1M1-WP | 制造商:American Power Conversion Corp 功能描述:APC SMART-UPS VT MAINTENANCE B 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 10-20KVA 400V WALL - Bulk |
| SBPSU10K30FC1M1-WP | 制造商:Schneider Electric 功能描述:SMART-UPS VT BYPASS PANEL - Bulk 制造商:Schneider Electric 功能描述:APC Smart-UPS VT Maintenance Bypass Panel 10-30kVA 208V Wall Mount w/42 Pos. Dis |
| SBPSU20K30FC1M1 | 制造商:Schneider Electric 功能描述:APC SMART-UPS VT MAINTENANCE BYPASS PANEL 20-30KVA 208V FLOO - Bulk |
發布緊急采購，3分鐘左右您將得到回復。