- 您現在的位置：買賣IC網 > PDF目錄296408 > M58WR064KU70ZA6U (NUMONYX) 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 PDF資料下載
參數資料
| 型號： | M58WR064KU70ZA6U |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 4M X 16 FLASH 1.8V PROM, 70 ns, PBGA44 |
| 封裝： | 7.50 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, VFBGA-44 |
| 文件頁數： | 50/122頁 |
| 文件大?。?/td> | 2187K |
| 代理商： | M58WR064KU70ZA6U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
M58WRxxxKU, M58WRxxxKL
Command interface - factory program commands
33/123
6.3
Enhanced Factory Program command
The Enhanced Factory Program command programs large streams of data within any one
block. It greatly reduces the total programming time when a large number of words are
written to a block at any one time.
The use of the Enhanced Factory Program command requires certain operating conditions.
●
VPP must be set to VPPH
●
VDD must be within operating range
●
Ambient temperature TA must be 30°C ± 10°C
●
The targeted block must be unlocked
Dual operations are not supported during the enhanced factory program operation and the
command cannot be suspended.
For optimum performance the Enhanced Factory Program commands should be limited to a
maximum of 100 program/erase cycles per block. If this limit is exceeded the internal
algorithm continues to work properly but some degradation in performance is possible.
Typical program times are given in Table 18. If the block is protected then the enhanced
factory program operation aborts, the data in the block does not change, and the status
register outputs the error.
The Enhanced Factory Program command has four phases: the setup phase, the program
phase to program the data to the memory, the verify phase to check that the data has been
correctly programmed and reprogram if necessary and the exit phase. Refer to Table 9:
6.3.1
Setup phase
The Enhanced Factory Program command requires two bus write operations to initiate the
command.
●
The first bus cycle sets up the Enhanced Factory Program command.
●
The second bus cycle confirms the command.
The status register P/EC SR7 should be read to check that the P/EC is ready. After the
confirm command is issued, read operations output the status register data. The Read
Status Register command must not be issued or it is interpreted as data to program.
相關PDF資料 |
PDF描述 |
|---|---|
| M5L28FGNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT |
| M3L13TCNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT |
| M3L14FCNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT |
| M3L15TGNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT |
| M5L13TCNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1.544 MHz - 125 MHz, HCMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M58WR064T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit (4Mb x 16, Multiple Bank, Burst ) 1.8V Supply Flash Memory |
| M58WR064T100ZB6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit (4Mb x 16, Multiple Bank, Burst ) 1.8V Supply Flash Memory |
| M58WR064T70ZB6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit (4Mb x 16, Multiple Bank, Burst ) 1.8V Supply Flash Memory |
| M58WR064T85ZB6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:64 Mbit (4Mb x 16, Multiple Bank, Burst ) 1.8V Supply Flash Memory |
| M58WR128EB | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit 8Mb x 16, Multiple Bank, Burst 1.8V Supply Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。