參數資料
型號： LAN83C175
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 微控制器/微處理器
英文描述： Ethernet CARDBUS Integrated Controller With Modem Support
中文描述： 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP208
封裝： 28 X 28 MM, 1.40 MM HEIGHT, TQFP-208
文件頁數： 34/92頁
文件大?。?/td> 299K
代理商： LAN83C175
34
The remaining words in the EEPROM are
available to software for general purpose non-
volatile storage. The eeprom can be accessed
through the base address designated by the
Expansion
Rom
Base
configuration space for both the modem and
ethernet function.
Address
in
the
POWER DOWN MODE
The LAN83C175 has a power down feature
which allows it to consume less power when not
in use. The host may power down the
LAN83C175 by writing a 1 to the power down bit
in the general control register. When the bit is
set, the chip's internal system clock is gated off
to reduce switching current (the transmit and
receive clocks will be shut off internally if the
LAN83C175 is in loopback mode when power
down is set). While the LAN83C175 is powered
down, the host may read and write the
configuration registers or the general control
register. All other functions are disabled
(attempting any other operation will cause
unpredictable behavior). The power down bit
must only be set when the LAN83C175 is in its
idle state.
When the nRST pin is asserted, the LAN83C175
will automatically enter power down mode after
recalling the contents of the EEPROM. The
host may power up the LAN83C175 by writing a
0 to the power down bit. If the host wishes to
issue a software reset to the LAN83C175, the
power down bit must be cleared. When the
software reset has completed, the power down
bit will remain cleared and the LAN83C175 will
be ready to operate.
The power down bit does not affect the CardBus
clock inside the LAN83C175. Instead, the
LAN83C175 supports the CardBus clock run
function which allows the host system to slow
down or temporarily shut off the CardBus clock
at its source. The clock run function is
implemented according to the CardBus Mobile
design guide (revision 1.0).
JUMPER OPTIONS
There are several operational modes in the
LAN83C175 which are selected by "jumpers" at
power-up reset. Actual jumpers do not need to
be installed on the board. The options can be
set by external pull-up or pull-down resistors at
manufacturing time. Pins MD[2:0] are used to
make the jumper selections. The pins are
latched shortly after nRST goes inactive. The
jumpers are not sampled after soft reset. A pull-
down resistor sets the jumper value to 0, and a
pull-up sets it to 1. The jumpers are defined as
follows:
MD[2] BYPASS EEPROM RECALL - When set
to 1, the EEPROM recall is not performed after
power-up reset. Used for test purposes only.
MD[1:0] These should be pulled down to 0.
SOFT RESET
The software driver may reset the LAN83C175
to its initial state by setting the soft reset bit in
the general control register. All state machines
and pointers to the internal RAMS will be reset.
Soft reset can only take place when the
LAN83C175 is powered up. Soft reset does
NOT affect the configuration of the LAN83C175.
The configuration registers (excluding EEPROM
control) will only be reset and the EEPROM will
only be recalled after hard reset.
Each time the software driver is loaded, it must
set soft reset before enabling the LAN83C175 to
act as a bus master. The driver may be loaded
after a warm boot, and the LAN83C175 DMA
controllers could be left in an unknown state.
If the LAN83C175 is enabled as a bus master
before a soft reset is issued, the DMA
controllers could corrupt host memory with a
bus master operation that was started before the
warm boot. When the soft reset bit is set, the
LAN83C175 takes 15 CardBus clocks to re-
initialize itself. The device must not be
accessed within that time period.
相關PDF資料
PDF描述
LAN83C180 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C185 HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
LAN83C183-JD FAST ETHERNET PHYSICAL LAYER DEVICE
LAN83C180TQFP 10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C183 FAST ETHERNET PHYSICAL LAYER DEVICE
相關代理商/技術參數
參數描述
LAN83C175TQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMC Corporation of America 功能描述:83C175TQFP 制造商:SMSC 功能描述:
LAN83C175TQFP WAF 制造商:SMSC 功能描述:
LAN83C180 制造商:SMSC 制造商全稱:SMSC 功能描述:10/100 FAST ETHERNET PHY TRANSCEIVER
LAN83C180_01 制造商:SMSC 制造商全稱:SMSC 功能描述:10/100 Fast Ethernet PHY Transceiver
LAN83C180TQFP 制造商:SMSC 制造商全稱:SMSC 功能描述:10/100 Fast Ethernet PHY Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*