參數資料
型號： CYW15G0201DXB
廠商： Cypress Semiconductor Corp.
英文描述： Dual-channel HOTLink II Transceiver(雙通道HOTLink II收發器)
中文描述： 雙通道HOTLink II收發器（雙通道的HOTLink二收發器）
文件頁數： 9/46頁
文件大?。?/td> 661K
代理商： CYW15G0201DXB
CYW15G0201DXB
CYV15G0201DXB
CYP15G0201DXB
Document #: 38-02058 Rev. *H
Page 9 of 46
DECMODE
3-Level Select
[4]
Static Control Input
Decoder Mode Select
.
This input selects the behavior of the Decoder block.
When LOW, the Decoder is bypassed and raw 10-bit characters are passed to the Output
Register. When the Decoder is bypassed, RXCKSEL must be MID.
When MID, the Decoder is enabled and the Cypress Decoder table for Special Code
characters is used. When HIGH, the Decoder is enabled and the alternate Decoder table
for Special Code characters is used. See
Table 25
for a list of the Special Codes supported
in both encoded modes.
Receive Operating Mode
.
These inputs are interpreted to select one of nine operating
modes of the receive path. See
Table 13
for details.
Reframe Enable for All Channels
. Active HIGH. When HIGH, the framers in both channels
are enabled to frame per the presently enabled framing mode and selected framing
character.
Reframe Mode Select
. Used to control the type of character framing used to adjust the
character boundaries (based on detection of one or more framing characters in the received
serial bit stream). This signal operates in conjunction with the presently enabled channel
bonding mode, and the type of framing character selected.
RXMODE[1:
0]
RFEN
3-Level Select
[4]
Static Control Inputs
LVTTL input,
asynchronous,
internal pull-down
3-Level Select
[4]
Static Control Input
RFMODE
When LOW, the low-latency framer is selected. This will frame on each occurrence of the
selected framing character(s) in the received data stream. This mode of framing stretches
the recovered clock for one or multiple cycles to align that clock with the recovered data.
When MID, the Cypress-mode multi-byte parallel framer is selected. This requires a pair of
the selected framing character(s), on identical 10-bit boundaries, within a span of 50 bits,
before the character boundaries are adjusted. The recovered character clock remains in the
same phasing regardless of character offset.
When HIGH, the alternate mode multi-byte parallel framer is selected. This requires
detection of the selected framing character(s) of the allowed disparities in the received serial
bit stream, on identical 10-bit boundaries, on four directly adjacent characters. The
recovered character clock remains in the same phasing regardless of character offset.
Framing Character Select
. Used to control the character or portion of a character used for
character framing of the received data streams.
FRAMCHAR 3-Level Select
[4]
Static Control Input
When MID, the framer looks for both positive and negative disparity versions of the 8-bit
Comma character. When HIGH, the framer looks for both positive and negative disparity
versions of the K28.5 character. Configuring FRAMCHAR to LOW is reserved for
component test.
Device Control Signals
PARCTL
3-Level Select
[4]
Static Control Input
Parity Check/Generate Control
. Used to control the different parity check and generate
functions.
When LOW, parity checking is disabled, and the RXOPx outputs are all disabled (High-Z).
When
MID,
and
the
Encoder/Decoder
DECMODE
≠
LOW), TXDx[7:0] inputs are checked (along with TXOPx) for valid ODD parity,
and ODD parity is generated for the RXDx[7:0] outputs and presented on RXOPx. When
the Encoder and Decoder are disabled (TXMODE[1]
=
LOW, DECMODE
=
LOW), the
TXDx[7:0] and TXCTx[1:0] inputs are checked (along with TXOPx) for valid ODD parity, and
ODD parity is generated for the RXDx[7:0] and RXSTx[1:0] outputs and presented on
RXOPx. When HIGH, parity checking and generation are enabled. The TXDx[7:0] and
TXCTx[1:0] inputs are checked (along with TXOPx) for valid ODD parity, and ODD parity is
generated for the RXDx[7:0] and RXSTx[2:0] outputs and presented on RXOPx.
are
enabled
(TXMODE[1]
≠
LOW,
Pin Descriptions
CYP(V)(W)15G0201DXB Dual HOTLink II Transceiver (continued)
Pin Name
I/O Characteristics
Signal Description
相關PDF資料
PDF描述
CYW15G0401DXB Quad HOTLink II Transceiver(四熱連接II收發器)
CYW2330 Dual Serial Input PLL with 2.5-GHz and 600-MHz Prescalers
CYW2331 Dual Serial Input PLL with 2.0-GHz and 600-MHz Prescalers
CYW2336 Dual Serial Input PLL with 2.0- and 1.1-GHz Prescalers(帶2.0-GHz 預標定器的串聯輸入PLL)
CYW256OXC Multiconductor Paired Security UTP Cable; Number of Conductors:8; Conductor Size AWG:23; No. Strands x Strand Size:Solid; Jacket Material:Polyvinylchloride (PVC); Number of Pairs:4; Impedance:100ohm; Jacket Color:Gray RoHS Compliant: Yes
相關代理商/技術參數
參數描述
CYW15G0201DXB-BBC 功能描述:電信線路管理 IC Dual Ch XCVR COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
CYW15G0201DXB-BBI 功能描述:電信線路管理 IC Dual Ch XCVR IND RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
CYW15G0201DXB-BBXC 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Dual-channel HOTLink II⑩ Transceiver
CYW15G0201DXB-BBXI 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Dual-channel HOTLink II⑩ Transceiver
CYW15G0401DXB 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Quad HOTLink II⑩ Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*