參數資料
型號： CYRF69213
廠商： Cypress Semiconductor Corp.
英文描述： Programmable Radio on Chip Low Power
中文描述： 可編程片上無線電低功耗
文件頁數： 17/85頁
文件大?。?/td> 731K
代理商： CYRF69213
CYRF69213
Document #: 001-07552 Rev. *B
Page 17 of 85
not match the expected values, the M8C will halt (with the
exception of the SWBootReset function). The following code
puts the correct value in KEY1 and KEY2. The code starts with
a halt, to force the program to jump directly into the setup code
and not run into it.
halt
SSCOP: mov [KEY1], 3ah
mov X, SP
mov A, X
add A, 3
mov [KEY2], A
The SROM also features Return Codes and Lockouts.
Return Codes
Return codes aid in the determination of success or failure of
a particular function. The return code is stored in KEY1’s
position in the parameter block. The CheckSum and
TableRead functions do not have return codes because
KEY1’s position in the parameter block is used to return other
data.
Read, write, and erase operations may fail if the target block
is read or write protected. Block protection levels are set
during device programming.
The EraseAll function overwrites data in addition to leaving the
entire user Flash in the erase state. The EraseAll function
loops through the number of Flash macros in the product,
executing the following sequence: erase, bulk program all
zeros, erase. After all the user space in all the Flash macros
are erased, a second loop erases and then programs each
protection block with zeros.
SROM Function Descriptions
All SROM functions are described in the following sections.
SWBootReset Function
The SROM function, SWBootReset, is the function that is
responsible for transitioning the device from a reset state to
running user code. The SWBootReset function is executed
whenever the SROM is entered with an M8C accumulator
value of 00h; the SRAM parameter block is not used as an
input to the function. This will happen, by design, after a
hardware reset, because the M8C's accumulator is reset to
00h or when user code executes the SSC instruction with an
accumulator value of 00h. The SWBootReset function will not
execute when the SSC instruction is executed with a bad key
value and a nonzero function code. A CYRF69213 device will
execute the HALT instruction if a bad value is given for either
KEY1 or KEY2.
The SWBootReset function verifies the integrity of the
calibration data by way of a 16-bit checksum, before releasing
the M8C to run user code.
ReadBlock Function
The ReadBlock function is used to read 64 contiguous bytes
from Flash—a block.
The first thing this function does is to check the protection bits
and determine if the desired BLOCKID is readable. If read
protection is turned on, the ReadBlock function will exit, setting
the accumulator and KEY2 back to 00h. KEY1 will have a
value of 01h, indicating a read failure. If read protection is not
enabled, the function will read 64 bytes from the Flash using
a ROMX instruction and store the results in SRAM using an
MVI instruction. The first of the 64 bytes will be stored in SRAM
at the address indicated by the value of the POINTER
parameter. When the ReadBlock completes successfully, the
accumulator, KEY1, and KEY2 will all have a value of 00h.
WriteBlock Function
The WriteBlock function is used to store data in the Flash. Data
is moved 64 bytes at a time from SRAM to Flash using this
function. The first thing the WriteBlock function does is to
check the protection bits and determine if the desired
BLOCKID is writable. If write protection is turned on, the Write-
Block function will exit, setting the accumulator and KEY2 back
to 00h. KEY1 will have a value of 01h, indicating a write failure.
The configuration of the WriteBlock function is straightforward.
The BLOCKID of the Flash block, where the data is stored,
must be determined and stored at SRAM address FAh.
The SRAM address of the first of the 64 bytes to be stored in
Flash must be indicated using the POINTER variable in the
parameter block (SRAM address FBh). Finally, the CLOCK
Table 21.SROM Function Parameters
Variable Name
SRAM Address
0,F8h
0,F9h
0,FAh
0,FBh
0,FCh
0,FDh
0,FEh
0,FFh
Key1/Counter/Return Code
Key2/TMP
BlockID
Pointer
Clock
Mode
Delay
PCL
Table 22.SROM Return Codes
Return Code
00h
01h
Description
Success
Function not allowed due to level of protection
on block
Software reset without hardware reset
Fatal error, SROM halted
02h
03h
Table 23.ReadBlock Parameters
Name
KEY1
KEY2
Address
0,F8h
0,F9h
Description
3Ah
Stack Pointer value, when SSC is
executed
Flash block number
First of 64 addresses in SRAM
where returned data should be
stored
BLOCKID
POINTER
0,FAh
0,FBh
[+] Feedback
相關PDF資料
PDF描述
CYRF69213-40LFXC Programmable Radio on Chip Low Power
CYRF6936-40LFXC WirelessUSB⑩ LP 2.4 GHz Radio SoC
CYS25G0101DX-ATC SONET OC-48 Transceiver
CYS25G0101DX-ATI SONET OC-48 Transceiver
CYS25G0101DX-ATXC SONET OC-48 Transceiver
相關代理商/技術參數
參數描述
CYRF69213_08 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Programmable Radio on Chip Low Power
CYRF69213_13 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Programmable Radio on Chip Low Power
CYRF69213-40LFXC 功能描述:射頻接收器 PRoC LP COM RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel
CYRF69213-40LTXC 功能描述:8位微控制器 -MCU Programmable Radio on Chip Low Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
CYRF69213A-40LFXC 功能描述:8位微控制器 -MCU Programmable Radio on Chip Low Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*