- 您現在的位置：買賣IC網 > PDF目錄375267 > ADSP-2192 (Analog Devices, Inc.) DSP Microcomputer PDF資料下載
參數資料
| 型號： | ADSP-2192 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | DSP Microcomputer |
| 中文描述： | DSP微機 |
| 文件頁數： | 35/40頁 |
| 文件大小： | 1307K |
| 代理商： | ADSP-2192 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁
–35–
REV. 0
ADSP-2192M
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram (
Figure 17
). If multiple
pins (such as the data bus) are enabled, the measurement value
is that of the first pin to start driving.
Example System Hold Time Calculation
To determine the data output hold time in a particular system,
first calculate t
DECAY
using the equation at
Output Disable Time
on Page 34
. Choose
V to be the difference between the ADSP-
2192M’s output voltage and the input threshold for the device
requiring the hold time. A typical
V will be 0.4 V. C
L
is the total
bus capacitance (per data line), and I
L
is the total leakage or three-
state current (per data line). The hold time will be t
DECAY
plus the
minimum disable time (i.e., t
DATRWH
for the write cycle).
Capacitive Loading
Output delays and holds are based on standard capacitive loads:
50 pF on all pins. The delay and hold specifications given should
be derated for loads other than the nominal value of 50 pF.
Environmental Conditions
The thermal characteristics in which the DSP is operating
influence performance (see
Table 38
).
Figure 17. Output Enable/Disable
Figure 18. Equivalent Device Loading for AC
Measurements (Includes All Fixtures)
REFERENCE
SIGNAL
t
DIS
OUTPUT STARTS
DRIVING
V
OH (MEASURED)
–
V 2.0V
V
OL (MEASURED)
+
V 1.0V
t
MEASURED
V
OH (MEASURED)
V
OL (MEASURED)
HIGH IMPEDANCE STATE.
TEST CONDITIONS CAUSE THIS VOLTAGE
TO BE APPROXIMATELY 1.5V
OUTPUT STOPS
DRIVING
t
DECAY
t
ENA
1.5V
50pF
TO
OUTPUT
PIN
I
OL
I
OH
Figure 19. Voltage Reference Levels for AC
Measurements (Except Output Enable/Disable)
Table 38. Thermal Characteristics
Rating Description
Symbol
LQFP
Thermal Resistance
(Junction-to-Ambient)
θ
JA
33.79°C/W
Still Air
INPUT
OR
OUTPUT
1.5V
1.5V
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-219212MKST160 | DSP Microcomputer |
| ADSP-2192M | DSP Microcomputer |
| ADSP-21992 | Mixed Signal DSP Controller With CAN |
| ADSP-21992YST | Mixed Signal DSP Controller With CAN |
| ADSP-21MOD970-510 | Multiport Internet Gateway Processor Data Pump Solution(多端口網關處理器數據泵解決方案) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2195MBCA-140 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 140MHz 140MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:16-BIT,140 MIPS, 2.5V, 80KBYTES RAM - Bulk |
| ADSP-2195MBST-140 | 功能描述:IC DSP CONTROLLER 16BIT 144LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-2195MKCA-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 160MHz 160MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:16-BIT,160 MIPS, 2.5V, 80KBYTES RAM - Bulk |
| ADSP-2195MKST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 24-Bit 160MHz 160MIPS 144-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| adsp-2196mbca-140 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。