- 您現在的位置：買賣IC網 > PDF目錄223308 > ADE7878ACPZ-RL (ANALOG DEVICES INC) Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind PDF資料下載
參數資料
| 型號： | ADE7878ACPZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40 |
| 文件頁數： | 14/96頁 |
| 文件大?。?/td> | 1096K |
| 代理商： | ADE7878ACPZ-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
ADE7854/ADE7858/ADE7868/ADE7878
Rev. E | Page 21 of 96
POWER MANAGEMENT
The ADE7868/ADE7878 have four modes of operation, deter-
mined by the state of the PM0 and PM1 pins (see Table 9). The
ADE7854/ADE7858 have two modes of operation. These pins
provide complete control of the ADE7854/ADE7858/ADE7868/
ADE7878 operation and can easily be connected to an external
microprocessor I/O. The PM0 and PM1 pins have internal pull-
recommended before and after setting a new power mode.
Table 9. Power Supply Modes
Power Supply Modes
PM1
PM0
PSM0, Normal Power Mode
0
1
0
1
0
PSM3, Sleep Mode
1
1 Available in the ADE7868 and ADE7878.
PSM0—NORMAL POWER MODE (ALL PARTS)
In PSM0 mode, the ADE7854/ADE7858/ADE7868/ADE7878
are fully functional. The PM0 pin is set to high and the PM1 pin
is set to low for the ADE78xx to enter this mode. If the ADE78xx
is in one of PSM1, PSM2, or PSM3 modes and is switched into
PSM0 mode, then all control registers take the default values with
the exception of the threshold register, LPOILVL, which is used
in PSM2 mode, and the CONFIG2 register, both of which
maintain their values.
The ADE7854/ADE7858/ADE7868/ADE7878 signal the end of
the transition period by triggering the IRQ1 interrupt pin low and
setting Bit 15 (RSTDONE) in the STATUS1 register to 1. This bit is
0 during the transition period and becomes 1 when the transition is
finished. The status bit is cleared and the IRQ1 pin is set back to
high by writing to the STATUS1 register with the corresponding
bit set to 1. Bit 15 (RSTDONE) in the interrupt mask register
does not have any functionality attached even if the IRQ1 pin goes
low when Bit 15 (RSTDONE) in the STATUS1 register is set to 1.
This makes the RSTDONE interrupt unmaskable.
PSM1—REDUCED POWER MODE (ADE7868,
ADE7878 ONLY)
The reduced power mode, PSM1, is available on the ADE7868
and ADE7878 only. In this mode, the ADE7868/ADE7878
measure the mean absolute values (mav) of the 3-phase currents
and store the results in the AIMAV, BIMAV, and CIMAV 20-bit
registers. This mode is useful in missing neutral cases in which
the voltage supply of the ADE7868 or ADE7878 is provided by an
external battery. The serial ports, I2C or SPI, are enabled in this
mode; the active port can be used to read the AIMAV, BIMAV,
and CIMAV registers. It is not recommended to read any of the
other registers because their values are not guaranteed in this
mode. Similarly, a write operation is not taken into account by
the ADE7868/ADE7878 in this mode.
In summary, in this mode, it is not recommended to access any
register other than AIMAV, BIMAV, and CIMAV. The circuit
that measures these estimates of rms values is also active during
PSM0; therefore, its calibration can be completed in either PSM0
mode or in PSM1 mode. Note that the ADE7868 and ADE7878
do not provide any register to store or process the corrections
resulting from the calibration process. The external microprocessor
stores the gain values in connection with these measurements
and uses them during PSM1 (see the Current Mean Absolute
Value Calculation—ADE7868 and ADE7878 Only section for
more details on the xIMAV registers).
The 20-bit mean absolute value measurements done in PSM1,
although available also in PSM0, are different from the rms
measurements of phase currents and voltages executed only in
PSM0 and stored in the xIRMS and xVRMS 24-bit registers. See
ADE7878 Only section for details.
If the ADE7868/ADE7878 is set in PSM1 mode while still in the
PSM0 mode, the ADE7868/ADE7878 immediately begin the
mean absolute value calculations without any delay. The xIMAV
registers are accessible at any time; however, if the ADE7878 or
ADE7868 is set in PSM1 mode while still in PSM2 or PSM3
modes, the ADE7868/ADE7878 signal the start of the mean
absolute value computations by triggering the IRQ1 pin low.
The xIMAV registers can be accessed only after this moment.
PSM2—LOW POWER MODE (ADE7868, ADE7878
ONLY)
The low power mode, PSM2, is available on the ADE7868 and
ADE7878 only. In this mode, the ADE7868/ADE7878 compare
all phase currents against a threshold for a period of 0.02 ×
(LPLINE[4:0] + 1) seconds, independent of the line frequency.
LPLINE[4:0] are Bits[7:3] of the LPOILVL register (see Table 10).
Table 10. LPOILVL Register
Bit
Mnemonic
Default
Description
[2:0]
LPOIL[2:0]
111
Threshold is put at a value
corresponding to full scale
multiplied by LPOIL/8.
[7:3]
LPLINE[4:0]
00000
The measurement period is
(LPLINE[4:0] + 1)/50 sec.
The threshold is derived from Bits[2:0] (LPOIL[2:0]) of the
LPOILVL register as LPOIL[2:0]/8 of full scale. Every time
one phase current becomes greater than the threshold, a
counter is incremented. If every phase counter remains below
LPLINE[4:0] + 1 at the end of the measurement period, then
the IRQ0 pin is triggered low. If a single phase counter becomes
greater or equal to LPLINE[4:0] + 1 at the end of the measure-
ment period, the IRQ1 pin is triggered low.
illustrates
how the ADE7868/ADE7878 behave in PSM2 mode when
相關PDF資料 |
PDF描述 |
|---|---|
| ADG529FTQ | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP18 |
| ADJ24006 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.042A (COIL), 6VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24012 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.021A (COIL), 12VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24024 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.01A (COIL), 24VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24048 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.005A (COIL), 48VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7880ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7903ARWZ | 功能描述:Energy Monitor (Power Meter) 24 bit SPI 20-SOIC 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:有效 類型:能量監測器（功率計） 分辨率（位）:24 b 采樣率（每秒）:- 數據接口:SPI 電壓源:單電源 電壓 - 電源:2.97 V ~ 3.63 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:20-SOIC 標準包裝:37 |
發布緊急采購，3分鐘左右您將得到回復。