- 您現在的位置：買賣IC網 > PDF目錄1890 > AD5560JSVUZ-REEL (Analog Devices Inc)IC DPS PROGRAMABLE W/DAC 64TQFP PDF資料下載
參數資料
| 型號： | AD5560JSVUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 39/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DPS PROGRAMABLE W/DAC 64TQFP |
| 設計資源： | Integrated Device Power Supply for PAD with Output Voltage Range 0 V to 25 V (CN0130) |
| 標準包裝： | 1,500 |
| 類型： | 電源 |
| 應用： | 自動測試設備 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-TQFP 裸露焊盤 |
| 供應商設備封裝： | 64-TQFP-EP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
AD5560
Data Sheet
Rev. D | Page 44 of 68
SERIAL INTERFACE
The AD5560 contains an SPI-compatible interface operating at
clock frequencies of up to 50 MHz. To minimize both the
power consumption of the device and on-chip digital noise, the
interface powers up fully only when the device is being written
to, that is, on the falling edge of SYNC.
SPI INTERFACE
The serial interface is 2.5 V LVTTL-compatible when operating
from a 2.3 V to 3.6 V DVCC supply. It is controlled by the
following four pins:
SYNC (frame synchronization input)
SDI (serial data input pin)
SCLK (clocks data in and out of the device)
SDO (serial data output pin for data readback)
SPI WRITE MODE
The AD5560 allows writing of data via the serial interface to
every register directly accessible to the serial interface, which
is all registers except the DAC registers.
The serial word is 24 bits long. The serial interface works with
both a continuous and a burst (gated) serial clock. Serial data
applied to SDI is clocked into the AD5560 by clock pulses applied
to SCLK. The first falling edge of SYNC starts the write cycle.
At least 24 falling clock edges must be applied to SCLK to clock
in 24 bits of data before SYNC is taken high again.
The input register addressed is updated on the rising edge of
SYNC. For another serial transfer to take place, SYNC must be
taken low again.
SDO OUTPUT
The SDO output in the AD5560 is a weak/slow output driver.
If using readback or the daisy-chain function, the frequency of
SCLK must be reduced so that SDO can operate properly. The
SCLK frequency is dependent on the DVCC supply voltage used;
see Table 2 for details and the following example:
Maximum SCLK = 12 MHz, then DVCC = 2.3 V to 2.7 V
Maximum SCLK = 15 MHz, then DVCC = 2.7 V to 3.3 V
Maximum SCLK = 20 MHz, then DVCC = 4.5 V to 5.5 V
RESET FUNCTION
RESET is a level-sensitive input. Bringing the RESET line low
resets the contents of all internal registers to their power-on
reset state. The falling edge of RESET initiates the reset process;
BUSY goes low for the duration, returning high when the
RESET process is complete. This sequence takes 300 s
maximum. Do not write to the serial interface while BUSY
is low handling a RESET command. When BUSY returns high,
normal operation resumes, and the status of the RESET pin is
ignored until it goes low again.
BUSY FUNCTION
BUSY is a digital open-drain output that indicates the status of
the AD5560. All writes drive the BUSY output low for some
period of time; however, events that use the calibration engine,
such as all DAC x1 writes, drive it lower for a longer period of
time while the calculations are completed.
For the DACs, the value of the internal data (x2) loaded to the
DAC data register is calculated each time the user writes new
data to the corresponding x1 register. During the calculation
of x2, the BUSY output goes low and x2 writes are pipelined;
therefore, x2 writes can still be presented to the device while
BUSY is still low (see the Register Update Rates section). The
DAC outputs update immediately after BUSY goes high.
Writes to other registers must be handled differently and
should either watch the BUSY pin or be timed. While BUSY
is low, the user can continue writing new data to any control
register, m register, or c register but should not complete the
writing process (SYNC returning high) until the BUSY signal
has returned high.
BUSY also goes low during power-on reset, as well as when a
low level is detected on the RESET pin.
BUSY writes to the system control register, compensation
register, alarm register, and diagnostic register; m or c registers
do not involve the calibration engine, thus speeding up writing
to the device.
LOAD FUNCTION
The AD5560 device contains a function with which updates
to multiple devices can be synchronized using the LOAD
function. There is not a dedicated pin available for this
function; however, either the CLEN or HW_INH pin can
be used as a LOAD input (selection is made in the system
control register, Address 0x1, Bits[8:7]).
When selected as the LOAD function, the pin no longer
operates in its previous function (power-on default for each
of these pins is a CLEN or HW_INH function).
The LOAD function controls the following registers:
0x8 FIN DAC x2 register
0xD CLL DAC x2 register
0x10 CLH DAC x2 register
0x4 Compensation Register 1
0x5 Compensation Register2
0x2 DPS Register1 (only current ranges, Bits[13:11])
There is, however, an alternate method for updating and using
the CLEN and HW_INH pins in their normal function.
相關PDF資料 |
PDF描述 |
|---|---|
| AD557JN | IC DAC 8BIT V-OUT 16-DIP |
| AD561KD | IC DAC 10BIT 5-15V IN MONO 16DIP |
| AD565AKD | IC DAC 12BIT MONO 250NS 24-CDIP |
| AD5663BCPZ-R2 | IC DAC NANO 16BIT DUAL 10-LFCSP |
| AD5678BRUZ-1 | IC DAC 12/16BIT SPI/SRL 14TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5561JBCZ | 制造商:Analog Devices 功能描述: |
| AD5562ACPZ-R7 | 制造商:Analog Devices 功能描述: |
| AD5564B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| AD557 | 制造商:AD 制造商全稱:Analog Devices 功能描述:a DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD557_01 | 制造商:AD 制造商全稱:Analog Devices 功能描述:a DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
發布緊急采購，3分鐘左右您將得到回復。