- 您現在的位置：買賣IC網 > PDF目錄373786 > ZL50119GAG (ZARLINK SEMICONDUCTOR INC) 32, 64 and 128 Channel CESoP Processors PDF資料下載
參數資料
| 型號： | ZL50119GAG |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | 32, 64 and 128 Channel CESoP Processors |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA324 |
| 封裝： | 23 X 23 MM, 2.03 MM HEIGHT, 1 MM PITCH, PLASTIC, MS-034, BGA-324 |
| 文件頁數： | 63/95頁 |
| 文件大?。?/td> | 1157K |
| 代理商： | ZL50119GAG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
ZL50115/16/17/18/19/20
Data Sheet
63
Zarlink Semiconductor Inc.
DPLL Loop Filter
DPLL Limiter (phase slope)
Although a short phase lock time is desirable, it is not always achievable due to other synchroniser requirements.
For instance, better jitter transfer performance is obtained with a lower frequency loop filter which increases locking
time; and a better (smaller) phase slope performance will increase locking time. Additionally, the locking time is
dependent on the p_shift value.
The DPLL Loop Filter and Limiter have been optimised to meet the Telcordia GR-1244-CORE jitter transfer and
phase alignment speed requirements. The phase lock time is guaranteed to be no greater than 30 seconds when
using the recommended Stratum 3 and Stratum 4/4E register settings.
9.6 Lock Status
The DPLL has a Lock Status Indicator and a corresponding Lock Change Interrupt. The response of the Lock
Status Indicator is a function of the programmed Lock Detect Interval (LDI) and Lock Detect Threshold (LDT) values
in the dpll_ldetect register. The LDT register can be programmed to set the jitter tolerance level of the Lock Status
Indicator. To determine if the DPLL has achieved lock the Lock Status Indicator must be high for a period of at least
30 seconds. When the DPLL loses lock the Lock Status Indicator will go low after LDI x 125
μ
s.
9.7 Jitter
The DPLL is designed to withstand, and improve inherent jitter in the TDM clock domain.
9.7.1 Acceptance of Input Wander
For T1(1.544 MHz), E1(2.048 MHz) and J2(6.312 MHz) input frequencies, the DPLL will accept a wander of up to
±1023UI
pp
at 0.1 Hz to conform with the relevant specifications. For the 8 kHz (frame rate) and 64 kHz (the divided
down output for T3/E3) input frequencies, the wander acceptance is limited to ±1 UI (0.1 Hz). This principle is
illustrated in Table 24.
9.7.2 Intrinsic Jitter
Intrinsic jitter is the jitter produced by a synchronizer and measured at its output. It is measured by applying a jitter
free reference signal to the input of the device, and measuring its output jitter. Intrinsic jitter may also be measured
when the device is in a non synchronizing mode such as free running or holdover, by measuring the output jitter of
the device. Intrinsic jitter is usually measured with various band-limiting filters, depending on the applicable
standards.
The intrinsic jitter in the DPLL is reduced to less than 1 ns p-p
1
by an internal Tapped Delay Line (TDL). The DPLL
can be programmed so that the output clock meets all the Stratum 3 requirements of Telcordia GR-1244-CORE.
Stratum 4/4E is also supported.
9.7.3 Jitter Tolerance
Jitter tolerance is a measure of the ability of a PLL to operate properly without cycle slips (i.e., remain in lock and/or
regain lock in the presence of large jitter magnitudes at various jitter frequencies) when jitter is applied to its
reference. The applied jitter magnitude and the jitter frequency depends on the applicable standards.
The DPLL’s jitter tolerance can be programmed to meet Telcordia GR-1244-CORE DS1 reference input jitter
tolerance requirements.
1. There are 2 exceptions to this. a) When reference is 8 kHz, and reference frequency offset relative to the master is small, jitter up to 1 master
clock period is possible, i.e. 10 ns p-p. b) In holdover mode, if a huge amount of jitter had been present prior to entering holdover, then an
additional 2 ns p-p is possible.
相關PDF資料 |
PDF描述 |
|---|---|
| ZL50120GAG | 32, 64 and 128 Channel CESoP Processors |
| ZL50118GAG | Connector assemblies, Network cables; |
| ZL50117GAG | REFLECTIVE PHOTOSENSOR SMD RSS42 |
| ZL50115 | 32, 64 and 128 Channel CESoP Processors |
| ZL50116 | 32, 64 and 128 Channel CESoP Processors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL50119GAG2 | 制造商:Microsemi Corporation 功能描述:64 CHANNEL CESOP PROCESSOR 制造商:Microsemi Corporation 功能描述:CESOP PROCESSOR 324BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 64CH 324PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 64CH 324PBGA |
| ZL50120 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:32, 64 and 128 Channel CESoP Processors |
| ZL50120GAG | 制造商:Microsemi Corporation 功能描述:CH CESOP PROCESSORS 324BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 128CH 324PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 128CH 324PBGA |
| ZL50120GAG2 | 制造商:Microsemi Corporation 功能描述:CESOP PROCESSOR 324BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 128CH 324PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 128CH 324PBGA |
| ZL50130 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Ethernet Pseudo-Wires across a PSN |
發布緊急采購，3分鐘左右您將得到回復。