參數資料
型號： TSPC860XRVZQU66D
廠商： Atmel Corp.
英文描述： Integrated Communication Processor
中文描述： 綜合通信處理器
文件頁數： 26/93頁
文件大小： 1601K
代理商： TSPC860XRVZQU66D
26
TSPC860 [Preliminary]
2129B–HIREL–12/04
Table 2 summarizes when active pull-up drivers are enabled as outputs.
The purpose of active pull-up buffers is to allow access to zero wait-state logic that
drives a shared signal on the clock cycle immediately following a cycle in which the sig-
nal is driven by the TSPC860. In other words, it eliminates the need for a bus turn-
around cycle.
Internal Pull-up and Pull-
down Resistors
The TMS and TRST pins have internal pull-up resistors. TSPC860 devices from Rev 0
to Rev A.3 (masks xE64C and xF84C) have an internal pull-up resistor on TCK/DSCK
but no internal pull-up resistor on TDI/DSDI. This was corrected on Rev B and later; on
these chips, the internal pull-up resistor was removed from TCK/DSCK and an internal
pull-up resistor was added to TDI/DSDI.
If RSTCONF is pulled down, during hardware reset (initiated by HRESET or PORE-
SET), the data bus D[0-31] is pulled down with internal pull-down resistors. These
internal pull-down resistors are to provide a logic-zero default for these pins when pro-
gramming the hard reset configuration word. These internal pull-down resistors are
disconnected after HRESET is negated.
No other pins have internal pull-ups or pull-downs.
Resistance values for internal pull-up and pull-down resistors are not specified because
their values may vary due to process variations and shrinks in die size, and they are not
tested. Typical values are on the order of 5 K
but can vary by approximately a factor
of 2.
Recommended Basic Pin
Connections
Reset Configuration
Some external pin configuration is determined at reset by the hard reset configuration
word. Thus, some decisions as to system configuration (for example, location of BDM
pins) should be made before required application of pull-up and pull-down resistors can
be determined.
RSTCONF should be grounded if the hard reset configuration word is used to configure
the TSPC860 or should be connected to V
CC
if the default configuration is used.
Pull-up resistors may not be used on D[0-31] to set the hard reset configuration word, as
the values of the internal pull-down resistors are not specified or guaranteed. To change
a data bus signal from its default logic low state during reset, actively drive that signal
high.
Table 2.
Active Pull-Up Resistors Enabled as Outputs
Signal
Description
TS, BB
When the TSPC860 is the external bus master throughout the entire bus cycle.
BI
When the TSPC860’s memory controller responds to the access on the external bus, throughout the entire bus cycle.
TA
When the TSPC860’s memory controller responds to the access on the external bus, then:
For chip-selects controlled by the GPCM set for external TA, the TSPC860’s TA buffer is not enabled as an output.
For chip-selects controlled by the GPCM set to terminate in n wait-states, TA is enabled as an output on cycle (n-1) and
driven high, then is driven low on cycle n, terminating the bus transaction. External logic can drive TA at any point before
this, thus terminating the cycle early. [For example, assume the GPCM is programmed to drive TA after 15 cycles. If
external logic drives TA before 14 clocks have elapsed then the TA will be accepted by the TSPC860 as a cycle
termination.]
For chip-selects controlled by the UPM, the TA buffer is enabled as an output throughout the entire bus cycle.
相關PDF資料
PDF描述
TSS10G45S SOLID STATE AC RELAY
TSS10J45S SOLID STATE AC RELAY
TSS2G45 TOSHIBA SOLID STATE AC RELAY
TSS2G47 TOSHIBA SOLID STATE AC RELAY
TSS2J45 TOSHIBA SOLID STATE AC RELAY
相關代理商/技術參數
參數描述
TSPC-DCM600 制造商:Traco Power 功能描述:Bulk
TSPCOS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TREND SERVER PROG MULTI
TSPCSP037G190A070 制造商:RAF Electronic Hardware 功能描述:
TSPD11CGPC0 功能描述:按鈕開關 SPST OFF-(ON) PC BLK RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
TSPD11CGPC004 功能描述:按鈕開關 SPST BLK PC MNT .4VA PUSHBUTTON SWITCH RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*