- 您現在的位置：買賣IC網 > PDF目錄192306 > S71PL191HB0BFI100 (SPANSION LLC) SPECIALTY MEMORY CIRCUIT, PBGA73 PDF資料下載
參數資料
| 型號： | S71PL191HB0BFI100 |
| 廠商： | SPANSION LLC |
| 元件分類： | 存儲器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA73 |
| 封裝： | 9 X 13 MM, LEAD FREE, FBGA-73 |
| 文件頁數： | 29/172頁 |
| 文件大小： | 4662K |
| 代理商： | S71PL191HB0BFI100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁
28
S29JL064H
S29JL064HA1 May 7, 2004
Pr el i m i n ary
If DQ5 goes high during a program or erase operation, writing the reset command
returns the banks to the read mode (or erase-suspend-read mode if that bank
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
The autoselect command sequence may be written to an address within a bank
that is either in the read or erase-suspend-read mode. The autoselect command
may not be written while the device is actively programming or erasing in another
bank.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the bank address and the au-
toselect command. The bank then enters the autoselect mode. The system may
read any number of autoselect codes without reinitiating the command sequence.
Table 4 shows the address and data requirements. To determine sector protection
information, the system must write to the appropriate bank address (BA) and
sector address (SA). Table 3 shows the address range and bank number associ-
ated with each sector.
The system must write the reset command to return to the read mode (or erase-
suspend-read mode if the bank was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The SecSi Sector region provides a secured data area containing a random, six-
teen-byte electronic serial number (ESN). The system can access the SecSi
Sector region by issuing the three-cycle Enter SecSi Sector command sequence.
The device continues to access the SecSi Sector region until the system issues
the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector com-
mand sequence returns the device to normal operation. The SecSi Sector is not
accessible when the device is executing an Embedded Program or embedded
Erase algorithm. Table 4 shows the address and data requirements for both com-
mand se quences. See also “SecSi (Secu red Silicon) Sector
Flash Memory Region” for further information. Note that the ACC function and un-
lock bypass modes are not available when the SecSi Sector is enabled.
Byte/Word Program Command Sequence
The system may program the device by word or byte, depending on the state of
the BYTE# pin. Programming is a four-bus-cycle operation. The program com-
mand sequence is initiated by writing two unlock write cycles, followed by the
program set-up command. The program address and data are written next, which
in turn initiate the Embedded Program algorithm. The system is not required to
provide further controls or timings. The device automatically provides internally
generated program pulses and verifies the programmed cell margin. Table 4
shows the address and data requirements for the byte program command
sequence.
When the Embedded Program algorithm is complete, that bank then returns to
the read mode and addresses are no longer latched. The system can determine
the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to the
Write Operation Status section for information on these status bits.
相關PDF資料 |
PDF描述 |
|---|---|
| S71VS128RC0ZHK203 | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| S71VS128RC0ZHK2L2 | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| S71WS512ND0BAWEH | SPECIALTY MEMORY CIRCUIT, PBGA84 |
| S72NS512PE0AHGL02 | SPECIALTY MEMORY CIRCUIT, PBGA133 |
| S7911 | PIN PHOTO DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71PL254 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM |
| S71PL254J | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM |
| S71PL254J04BAW0Z0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs |
| S71PL254J04BAW0Z2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs |
| S71PL254J04BAW0Z3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Based MCPs |
發布緊急采購，3分鐘左右您將得到回復。