- 您現在的位置：買賣IC網 > PDF目錄368020 > PI7C7300 (Pericom Semiconductor Corp.) 3-PORT PCI-to-PCI BRIDGE PDF資料下載
參數資料
| 型號： | PI7C7300 |
| 廠商： | Pericom Semiconductor Corp. |
| 英文描述： | 3-PORT PCI-to-PCI BRIDGE |
| 中文描述： | 3端口PCI至PCI橋 |
| 文件頁數： | 94/109頁 |
| 文件大?。?/td> | 779K |
| 代理商： | PI7C7300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
PI7C7300A
3-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 94 OF 109
09/25/03 Revision 1.09
valid. For reads, even parity must be generated using the initiators CBE signals combined
with the read data. Again, the PAR signal corresponds to read data from the previous
data phase cycle.
15.3.3
REPORTING PARITY ERRORS
For all address phases, if a parity error is detected, the error should be reported on the
P_SERR# signal by asserting P_SERR# for one cycle and then 3-stating two cycles after
the bad address. P_SERR# can only be asserted if bit 6 and 8 in the Command Register
are both set to 1. For write data phases, a parity error should be reported by asserting the
P_PERR# signal two cycles after the data phase and should remain asserted for one cycle
when bit 6 in the Command register is set to a 1. The target reports any type of data
parity errors during write cycles, while the master reports data parity errors during read
cycles.
Detection of an address parity error will cause the PCI-to-PCI Bridge target to not claim
the bus (P_DEVSEL# remains inactive) and the cycle will then terminate with a Master
Abort. When the bridge is acting as master, a data parity error during a read cycle results
in the bridge master initiating a Master Abort.
15.3.4
SECONDARY IDSEL MAPPING
When PI7C7300A detects a Type 1 configuration transaction for a device connected to
the secondary, it translates the Type 1 transaction to Type 0 transaction on the
downstream interface. Type 1 configuration format uses a 5-bit field at P_AD[15:11] as a
device number. This is translated to S1_AD[31:16] or S2_AD[31:16] by PI7C7300A.
16
IEEE 1149.1 COMPATIBLE JTAG CONTROLLER
An IEEE 1149.1 compatible Test Access Port (TAP) controller and associated TAP pins
are provided to support boundary scan in PI7C7300A for board-level continuity test and
diagnostics. The TAP pins assigned are TCK, TDI, TDO, TMS and TRST#. All digital
input, output, input/output pins are tested except TAP pins and clock pin.
The IEEE 1149.1 Test Logic consists of a TAP controller, an instruction register, and
a group of test data registers including Bypass, Device Identification and Boundary Scan
registers. The TAP controller is a synchronous 16-state machine driven by the Test Clock
(TCK) and the Test Mode Select (TMS) pins. An independent power on reset circuit is
provided to ensure the machine is in TEST_LOGIC_RESET state at power-up. The
JTAG signal lines are not active when the PCI resource is operating PCI bus cycles.
PI7C7300A implements 3 basic instructions: BYPASS, SAMPLE/PRELOAD, and
EXTEST.
相關PDF資料 |
PDF描述 |
|---|---|
| PI7C7300A | 3-PORT PCI-to-PCI BRIDGE |
| PI7C7300ANA | 3-PORT PCI-to-PCI BRIDGE |
| PI7C8140A | 2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON |
| PI7C8148B | 2-PORT PCI-to-PCI BRIDGE PLX PC16152 COMPARISON |
| PI7C8150B-33 | PCI Bridge | Asynchronous 2-Port PCI Bridge |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C7300A | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:3-PORT PCI-to-PCI BRIDGE |
| PI7C7300AEVB-3 | 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| PI7C7300ANA | 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 272-Pin BGA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 272-Pin BGA |
| PI7C7300ANAE | 功能描述:外圍驅動器與原件 - PCI 3 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C7300ANA-E | 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 272-Pin BGA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 272-Pin BGA |
發布緊急采購，3分鐘左右您將得到回復。