- 您現在的位置：買賣IC網 > PDF目錄363665 > NS32FX16-20 (National Semiconductor Corporation) Imaging/Signal Processor PDF資料下載
參數資料
| 型號： | NS32FX16-20 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Imaging/Signal Processor |
| 中文描述： | 影像/信號處理器 |
| 文件頁數： | 28/88頁 |
| 文件大小： | 902K |
| 代理商： | NS32FX16-20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
3.0 Functional Description
(Continued)
The Operand class columns give the Access Class for each
general operand, defining how the addressing modes are
interpreted (see Series 32000 Instruction Set Reference
Manual).
The Operand Issued columns show the sizes of the oper-
ands issued to the Floating-Point Unit by the CPU. ‘‘D’’ indi-
cates a 32-bit Double Word. ‘‘i’’ indicates that the instruction
specifies an integer size for the operand (B
e
Byte,
W
e
Word, D
e
Double Word). ‘‘f’’ indicates that the in-
struction specifies a Floating-Point size for the operand
(F
e
32-bit Standard Floating, L
e
64-bit Long Floating).
The Returned Value Type and Destination column gives the
size of any returned value and where the CPU places it. The
PSR Bits Affected column indicates which PSR bits, if any,
are updated from the Slave Processor Status Word (Figure
3-3).
TL/EE/10818–11
FIGURE 3-3. Slave Processor Status Word
Any operand indicated as being of type ‘‘f’’ will not cause a
transfer if the Register addressing mode is specified. This is
because the Floating-Point Registers are physically on the
Floating-Point Unit and are therefore available without CPU
assistance.
3.2 EXCEPTION PROCESSING
Exceptions are special events that alter the sequence of
instruction execution. The CPU recognizes two basic types
of exceptions: interrupts and traps.
An interrupt occurs in response to an event signalled by
activating the NMI or INT input signals. Interrupts are typi-
cally requested by peripheral devices that require the CPU’s
attention.
Traps occur as a result either of exceptional conditions
(e.g., attempted division by zero) or of specific instructions
whose purpose is to cause a trap to occur (e.g., supervisor
call instruction).
When an exception is recognized, the CPU saves the PC,
PSR and the MOD register contents on the interrupt stack
and then it transfers control to an exception service proce-
dure.
Details on the operations performed in the various cases by
the CPU to enter and exit the exception service procedure
are given in the following sections.
It is to be noted that the reset operation is not treated here
as an exception. Even though, like any exception, it alters
the instruction execution sequence.
The reason being that the CPU handles reset in a signifi-
cantly different way than it does for exceptions.
Refer to Section 3.5.4 for details on the reset operation.
3.2.1 Exception Acknowledge Sequence
When an exception is recognized, the CPU goes through
three major steps:
1) Adjustment of Registers.
Depending on the source of the exception, the CPU may
restore and/or adjust the contents of the Program Coun-
ter (PC), the Processor Status Register (PSR) and the
currently-selected Stack Pointer (SP). A copy of the PSR
is made, and the PSR is then set to reflect Supervisor
Mode and selection of the Interrupt Stack.
2) Vector Acquisition.
A Vector is either obtained from the Data Bus or is sup-
plied by default.
3) Service Call.
The Vector is used as an index into the Interrupt Dis-
patch Table, whose base address is taken from the CPU
Interrupt Base (INTBASE) Register. See Figure 3-4. A
32-bit External Procedure Descriptor is read from the ta-
ble entry, and an External Procedure Call is performed
using it. The MOD Register (16 bits) and Program Coun-
ter (32 bits) are pushed on the Interrupt Stack.
TL/EE/10818–12
FIGURE 3-4. Interrupt Dispatch and Cascade Tables
28
相關PDF資料 |
PDF描述 |
|---|---|
| NS32FX16-25 | Imaging/Signal Processor |
| NS32FX164-20 | Advanced Imaging/Communication Signal Processors(高級圖象/通訊信號處理器) |
| NS32FV16-25 | Advanced Imaging/Communication Signal Processors |
| NS32FX164-25 | Advanced Imaging/Communication Signal Processors(高級圖象/通訊信號處理器) |
| NS32FX161-15 | Advanced Imaging/Communication Signal Processors(高級圖象/通訊信號處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NS32FX16-25 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Imaging/Signal Processor |
| NS32FX164 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| NS32FX164-20 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Advanced Imaging/Communication Signal Processors |
| NS32FX164-25 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Advanced Imaging/Communication Signal Processors |
| NS32FX164AV-25 | 功能描述:IC IMAGING COMM SGNL PROC PLCC68 RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。