- 您現在的位置：買賣IC網 > PDF目錄374297 > K9F4G08U0M (SAMSUNG SEMICONDUCTOR CO. LTD.) 512M x 8 Bits / 1G x 8 Bits NAND Flash Memory PDF資料下載
參數資料
| 型號： | K9F4G08U0M |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 512M x 8 Bits / 1G x 8 Bits NAND Flash Memory |
| 中文描述： | 512M x 8位/ 1克× 8位NAND閃存 |
| 文件頁數： | 38/41頁 |
| 文件大?。?/td> | 1076K |
| 代理商： | K9F4G08U0M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁
FLASH MEMORY
38
Advance
K9F4G08U0M
K9K8G08U1M
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h command to the command register, a read cycle outputs
the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control allows
the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or CE
does not need to be toggled for updated status. Refer to Table 3 for specific Status Register definitions. The command register
remains in Status Read mode until further commands are issued to it. Therefore, if the status register is read during a random read
cycle, the read command(00h) should be given before starting read cycles.
Table 3. Staus Register Definition for 70h Command
NOTE
:
1. I/Os defined ’Not use’ are recommended to be masked out when Read Status is being executed.
I/O
Page Program
Block Erase
Read
Definition
I/O 0
Pass/Fail
Pass/Fail
Not use
Pass : "0" Fail : "1"
I/O 1
Not use
Not use
Not use
Don’t -cared
I/O 2
Not use
Not use
Not use
Don’t -cared
I/O 3
Not Use
Not Use
Not Use
Don’t -cared
I/O 4
Not Use
Not Use
Not Use
Don’t -cared
I/O 5
Not Use
Not Use
Not Use
Don’t -cared
I/O 6
Ready/Busy
Ready/Busy
Ready/Busy
Busy : "0" Ready : "1"
I/O 7
Write Protect
Write Protect
Write Protect
Protected : "0" Not Protected : "1"
READ EDC STATUS
Read EDC status operation is only available on ’Copy Back Program’. The device contains a EDC Status Register which may be
read to find out whether there is error during ’Read for Copy Back’. After writing 7Bh command to the command register, a read cycle
outputs the content of the EDC Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line
control allows the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired.
RE or CE does not need to be toggled for updated status. Refer to Table 4 for specific Status Register definitions. The command reg-
ister remains in EDC Status Read mode until further commands are issued to it.
Table 4. Status Register Definition for 7Bh Command
NOTE
:
1. I/Os defined ’Not use’ are recommended to be masked out when Read Status is being executed.
2. More than 2-bit error detection isn’t available for each 528B plane.
That is to say, only 1-bit error detection is avaliable for each 528B plane.
I/O
Copy Back Program
Page Program
Block Erase
Read
Definition
I/O 0
Pass/Fail of Copy Back Program
Pass/Fail
Pass/Fail
Not use
Pass : "0", Fail : "1"
I/O 1
EDC Status
Not use
Not use
Not use
No Error : "0", Error : "1"
I/O 2
Validity of EDC Status
Not use
Not use
Not use
Valid : "1", Invalid : "0"
I/O 3
Not Use
Not Use
Not Use
Not Use
Don’t -cared
I/O 4
Not Use
Not Use
Not Use
Not Use
Don’t -cared
I/O 5
Not Use
Not Use
Not Use
Not Use
Don’t -cared
I/O 6
Ready/Busy of Copy Back Program
Ready/Busy
Ready/Busy
Ready/Busy Busy : "0", Ready : "1"
I/O 7
Write Protect of Copy Back Program
Write Protect
Write Protect
Write Protect Protected : "0", Not Protected :"1"
相關PDF資料 |
PDF描述 |
|---|---|
| K9K8G08U1M | 512M x 8 Bits / 1G x 8 Bits NAND Flash Memory |
| K9F5608Q0C | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608Q0C-D | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608Q0C-H | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608U0C | 512Mb/256Mb 1.8V NAND Flash Errata |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9F4G08U0M-PCB0 | 制造商:Samsung Semiconductor 功能描述: |
| K9F4G08U0M-PCB0000 | 制造商:Samsung 功能描述:4GB SLC NORMAL X8 TSOP1 - Trays |
| K9F4G08U0M-PCB0T00 | 制造商:Samsung 功能描述:4GB SLC NORMAL X8 TSOP1 - Trays |
| K9F5608D0C | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit , 16M x 16 Bit NAND Flash Memory |
| K9F5608D0C-D | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32M x 8 Bit , 16M x 16 Bit NAND Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。