參數資料
型號： ISP1362EE
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Single-chip Universal Serial Bus On-The-Go controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
封裝： 6 X 6 MM, 0.80 HEIGHT, PLASTIC, MO-195, SOT-543-1, TFBGA-64
文件頁數： 45/150頁
文件大?。?/td> 647K
代理商： ISP1362EE
Philips Semiconductors
ISP1362
Single-chip USB OTG controller
Product data
Rev. 03
—
06 January 2004
45 of 150
9397 750 12337
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
placed in the ATL RAM at the same time. A paired PTD is designed specially for
high performance of a single endpoint. They are identi
fi
ed by hardware by using
the
‘
Paired
’
bit in the PTD.
Possible to send up to a maximum of 18 USB bulk packets in 1 ms frame
(1.152 Mbyte/s) by using the paired PTD feature.
Provides the status of every transfer endpoints (PTD) by monitoring the
HcATLDoneMap of the ISP1362. This register provides information on which PTD
transfers are complete.
Sets the IRQ after the user-speci
fi
ed number of transfers is done.
Skips any PTD that is wasting bandwidth by using HcATLSkipMap.
12.5.1
Sending a USB device request (Get Descriptor)
This section provides an example on how a USB transfer descriptor
‘
Get Descriptor
’
(commonly used in device enumeration) is used to illustrate the ISP1362 PTD
application. To perform this example, make sure the ISP1362 is in the Operational
state, and then connect a USB device (for example, a USB mouse) to a port.
Remark:
For details on the USB device request, refer to Chapter 9 of
Universal Serial
Bus Speci
fi
cation Rev. 2.0
.
Step 1:
Set the HcATLBlockSize, HcATLSkip and HcATLLast registers to 0x0008,
0xFFFE and 0x0001, respectively.
Step 2:
A PTD is then constructed based on the information given in the following
sample code. This sample code places information into the correct bit location within
the 8 bytes of the PTD structure.
ActualBytes (10 bits) = 0x00
CompletionCode (4 bits) = 0x0F
Active (1 bit) = 1
Toggle (1 bit) = 0
MaxPacketSize (10 bits) = 8
EndpointNumber (4 bits) = 0
Speed (1 bit) = 0 (full-speed; use 1 for low-speed)
DirToken (2 bits) = 0 (setup token)
TotalBytes (10 bits) = 8
CompletedPTD
0xF800, 0x0008, 0x0008, 0x0000
Step 3:
This array is then appended with an 8-byte payload that speci
fi
es the type of
request the HC wants to send. For example, for Get Descriptor, the payload is
0x0680, 0x0100, 0x0000, 0x0012.
Step 4:
The 16 bytes of data is now a complete PTD with an accompanying payload.
This array is then copied into the ATL buffer area.
Table 12
shows the ATL buffer area.
Step 5:
After copying data into the ATL buffer, the HC must be noti
fi
ed that the ATL
buffer is now full and ready to be processed. The ATL_Active bit of the
HcBufferStatus register must be set to logic 1 to inform the HC that the data in the
Table 12:
Offset
Data
ATL buffer area
0
0xF800
1
0x0008
2
0x0008
3
0x0000
4
0x0680
5
0x0100
6
0x0000
7
0x0012
相關PDF資料
PDF描述
ISP1501 Hi-Speed Universal Serial Bus peripheral transceiver
ISP1520 Hi-Speed Universal Serial Bus hub controller
ISP1520BD Hi-Speed Universal Serial Bus hub controller
ISP1521 Hi-Speed Universal Serial Bus hub controller
ISP1521BE Hi-Speed Universal Serial Bus hub controller
相關代理商/技術參數
參數描述
ISP1362EE,518 功能描述:USB 接口集成電路 USB OTG HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362EE,551 功能描述:USB 接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362EE,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1362EE/01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip Universal Serial Bus On-The-Go controller
ISP1362EE-S 功能描述:IC USB CTRL SNGL CHIP 64TFBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*