參數資料
型號: ICS1893AFLF
廠商: IDT, Integrated Device Technology Inc
文件頁數: 51/136頁
文件大?。?/td> 0K
描述: PHYCEIVER LOW PWR 3.3V 48-SSOP
標準包裝: 30
系列: PHYceiver™
類型: PHY 收發器
規程: MII
電源電壓: 3.14 V ~ 3.47 V
安裝類型: 表面貼裝
封裝/外殼: 48-BSSOP(0.295",7.50mm 寬)
供應商設備封裝: 48-SSOP
包裝: 管件
其它名稱: 1893AFLF
800-2353-5
ICS1893AFLF-ND
Chapter 5
Operating Modes Overview
ICS1893AF, Rev. D 10/26/04
October, 2004
21
ICS1893AF Data Sheet - Release
Copyright 2004, Integrated Circuit Systems, Inc.
All rights reserved.
5.1.2.3
Software Reset
Entering Software Reset
Initiation of a software reset occurs when a management entity writes a logic one to Control Register bit
0.15. When this write occurs, the ICS1893AF enters the reset state for two REF_IN clock cycles.
Note:
Entering a software reset is nearly identical to entering a hardware reset or a power-on reset,
except that during a software-initiated reset, the ICS1893AF does not enter the power-down state.
Exiting Software Reset
At the completion of a reset (either hardware, power-on, or software), the ICS1893AF sets all registers to
their default values. This action automatically clears (that is, sets equal to logic zero) Control Register bit
0.15, the software reset bit. Therefore, for a software reset (only), bit 0.15 is a self-clearing bit that indicates
the completion of the reset process.
Note:
1.
The RESETn pin is active low but Control Register bit 0.15 is active high.
2.
Exiting a software reset is nearly identical to exiting a hardware reset or a power-on reset, except that
upon exiting a software-initiated reset, the ICS1893AF does not re-latch its Serial Management Port
Address into the Extended Control Register. [For information on the Serial Management Port Address,
3.
The Control Register bit 0.15 does not represent the status of a hardware reset. It is a self-clearing bit
that is used to initiate a software reset. During a hardware or power-on reset, Control Register bit 0.15
does not get set to logic one. As a result, this bit 0.15 cannot be used to indicate the completion of the
reset process for hardware or power-on resets.
5.2
Power-Down Operations
The ICS1893AF enters the power-down state whenever either (1) the RESETn pin is low or (2) Control
Register bit 0.11 (the Power-Down bit) is logic one. In the power-down state, the ICS1893AF disables all
internal functions and drives all MAC/Repeater Interface output pins to logic zero except for those that
support the MII Serial Management Port. In addition, the ICS1893AF tri-states its Twisted-Pair Transmit
pins (TP_TXP and TP_TXN) to achieve an additional reduction in power.
There is one significant difference between entering the power-down state by setting Control Register bit
0.11 as opposed to entering the power-down state during a reset. When the ICS1893AF enters the
power-down state:
By setting Control Register bit 0.11, the ICS1893AF maintains the value of all Management Register bits
except for the latching low (LL), latching high (LH), and latching maximum (LMX) status bits. Instead,
these LL, LH, and LMX Management Register bits are re-initialized to their default values.
During a reset, the ICS1893AF sets all of its Management Register bits to their default values. It does not
maintain the state of any Management Register bit.
For more information on power-down operations, see the following:
Section 10.4, “DC Operating Characteristics”, which has tables that specify the ICS1893AF power
consumption while in the power-down state
相關PDF資料
PDF描述
VE-JNN-MY-F2 CONVERTER MOD DC/DC 18.5V 50W
ADCMP606BKSZ-R2 IC COMP TTL/CMOS 1CHAN SC70-6
VE-JNM-MY-F4 CONVERTER MOD DC/DC 10V 50W
MAX976EUA+ IC COMPARATOR DUAL 8-UMAX
ISL98003INZ-110 IC AFE 3CH 8BIT 110MHZ 80EPTQFP
相關代理商/技術參數
參數描述
ICS1893AFLFT 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
ICS1893AFT 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
ICS1893AG 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM
ICS1893AGI 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM
ICS1893AGILF 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM