- 您現在的位置：買賣IC網 > PDF目錄10742 > ICS1893AFLF (IDT, Integrated Device Technology Inc)PHYCEIVER LOW PWR 3.3V 48-SSOP PDF資料下載
參數資料
| 型號： | ICS1893AFLF |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 109/136頁 |
| 文件大小： | 0K |
| 描述： | PHYCEIVER LOW PWR 3.3V 48-SSOP |
| 標準包裝： | 30 |
| 系列： | PHYceiver™ |
| 類型： | PHY 收發器 |
| 規程： | MII |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 48-SSOP |
| 包裝： | 管件 |
| 其它名稱： | 1893AFLF 800-2353-5 ICS1893AFLF-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
ICS1893AF, Rev D 10/26/04
October, 2004
74
Chapter 8
Management Register Set
ICS1893AF Data Sheet - Release
Copyright 2004, Integrated Circuit Systems, Inc.
All rights reserved.
8.6.5
Technology Ability Field (bits 4.9:5)
When its Auto-Negotiation sublayer is enabled, the ICS1893AF transmits its link capabilities to its remote
link partner during the auto-negotiation process. The Technology Ability Field (TAF) bits 4.12:5 determine
the specific abilities that the ICS1893AF advertises. The ISO/IEC specification defines the TAF
technologies in Annex 28B.
The ISO/IEC specification reserves bits 4.12:10 for future use. When each of these reserved bits is:
Read by an STA, the ICS1893AF returns a logic zero
Written to by an STA, the STA must use the default value specified in this data sheet
ICS uses some reserved bits to invoke auxiliary functions. To ensure proper operation of the ICS1893AF,
an STA must maintain the default value of these bits. Therefore, ICS recommends that an STA always write
the default value of any reserved bits during all management register write operations.
Reserved bits 4.12:10 are Command Override Write (CW) bits. Whenever bit 16.15 (the Command
Register Override bit) is logic:
Zero, the ICS1893AF isolates all STA writes to CW bits, including bits 4.12:10.
One, an STA can modify the value of bits 4.12:10
Each of the bits 4.9:5 in the TAF represent a specific technology capability. When one of these bits is logic:
Zero, it indicates to the remote link partner that the local device cannot support the technology
represented by the bit.
One, it indicates to the remote link partner that the local device can support the technology.
With the exception of bit 4.9, the default settings of the TAF bits depend on the ICS1893AF operating
mode. Bit 4.9 is always logic zero, indicating that the ICS1893AF cannot support 100Base-T4 operations.
The TAF bits are Command Override Write bits. The default value of these bits depends on the signal level
on the HW/SW pin and whether the Auto-Negotiation sublayer is enabled.
With the Auto-Negotiation Enable bit (bit 0.12) set to logic:
Zero (that is, disabled), the ICS1893AF does not execute the auto-negotiation process. Upon completion
of the initialization sequence, the ICS1893AF proceeds to the Idle state and begins transmitting IDLES.
Two Control Register bits – the Data Rate Select bit (bit 0.13) and the Duplex Select bit (bit 0.8) –
determine the technology mode that the ICS1893AF uses for data transmission and reception. In this
mode, the values of the TAF bits (bits 4.8:5) are undefined.
One (that is, enabled), the ICS1893AF executes the auto-negotiation process and advertises its
capabilities to the remote link partner. The TAF bits (bits 4.8:5) determine the capabilities that the
ICS1893AF advertises to its remote link partner. For the ICS1893AF, all of these bits 4.8:5 are set to
logic one, indicating the ability of the ICS1893AF to provide these technologies.
Note:
1.
The ICS1893AF does not alter the value of the Status Register bits based on the TAF bits in
register 4, as the ISO/IEC definitions for the Status Register bits require these bits to indicate all the
capabilities of the ICS1893AF.
2.
The STA can alter the default TAF bit settings, 4.12:5, and subsequently issue an Auto-Negotiation
Restart.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JNN-MY-F2 | CONVERTER MOD DC/DC 18.5V 50W |
| ADCMP606BKSZ-R2 | IC COMP TTL/CMOS 1CHAN SC70-6 |
| VE-JNM-MY-F4 | CONVERTER MOD DC/DC 10V 50W |
| MAX976EUA+ | IC COMPARATOR DUAL 8-UMAX |
| ISL98003INZ-110 | IC AFE 3CH 8BIT 110MHZ 80EPTQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1893AFLFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| ICS1893AFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICS1893AG | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM |
| ICS1893AGI | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM |
| ICS1893AGILF | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 V 10Base-T/100Base-TX Integrated PHYceiver-TM |
發布緊急采購，3分鐘左右您將得到回復。