- 您現在的位置：買賣IC網 > PDF目錄362742 > EP7212-CV-A (CIRRUS LOGIC INC) HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) PDF資料下載
參數資料
| 型號： | EP7212-CV-A |
| 廠商： | CIRRUS LOGIC INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| 中文描述： | 32-BIT, MROM, 74 MHz, RISC MICROCONTROLLER, PQFP208 |
| 封裝： | LQFP-208 |
| 文件頁數： | 67/136頁 |
| 文件大?。?/td> | 2289K |
| 代理商： | EP7212-CV-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
EP7212
DS474PP1
67
5.3
5.3.1
Interrupt Registers
INTSR1 Interrupt Status Register 1
ADDRESS: 0x8000.0240
The interrupt status register is a 32-bit read only register. The interrupt status register reflects the cur-
rent state of the first 16 interrupt sources within the EP7212. Each bit is set if the appropriate interrupt
is active. The interrupt assignment is given in
Table 34
.
15
14
13
12
11
10
9
8
SSEOTI
7
EINT3
UMSINT
6
EINT2
URXINT1
5
EINT1
UTXINT1
4
CSINT
TINT
3
MCINT
RTCMI
2
WEINT
TC2OI
1
BLINT
TC1OI
0
EXTFIQ
Bit
Description
0
EXTFIQ
: External fast interrupt. This interrupt will be active if the nEXTFIQ input pin is forced low and is
mapped to the FIQ input on the ARM720T processor.
BLINT
: Battery low interrupt. This interrupt will be active if no external supply is present (nEXTPWR is
high) and the battery OK input pin BATOK is forced low. This interrupt is de-glitched with a 16 kHz clock,
so it will only generate an interrupt if it is active for longer than 125
μ
sec. It is mapped to the FIQ input
on the ARM720T processor and is cleared by writing to the BLEOI location.
NOTE:
BLINT is disabled during the Standby State.
WEINT
: Tick Watch dog expired interrupt. This interrupt will become active on a rising edge of the peri-
odic 64 Hz tick interrupt clock if the tick interrupt is still active (i.e., if a tick interrupt has not been ser-
viced for a complete tick period). It is mapped to the FIQ input on the ARM720T processor and the TEOI
location.
NOTE:
WEINT is disabled during the Standby State.
Watch dog timer tick rate is 64 Hz (in 13 MHz and 73.728–18.432 MHz modes).
Watchdog timer is turned off during the Standby State.
MCINT
: Media changed interrupt. This interrupt will be active after a rising edge on the nMEDCHG input
pin has been detected, This input is de-glitched with a 16 kHz clock so it will only generate an interrupt
if it is active for longer than 125
μ
sec. It is mapped to the FIQ input on the ARM7TDMI processor and is
cleared by writing to the MCEOI location. On power-up, the Media change pin (nMEDCHG) is used as
an input to force the processor to either boot from the internal Boot ROM, or from external memory.
After power-up, the pin can be used as a general purpose FIQ interrupt pin.
CSINT
: Codec sound interrupt, generated when the data FIFO has reached half full or empty (depend-
ing on the interface direction). It is cleared by writing to the COEOI location.
EINT1
: External interrupt input 1. This interrupt will be active if the nEINT1 input is active (low). It is
cleared by returning nEINT1 to the passive (high) state.
EINT2
: External interrupt input 2. This interrupt will be active if the nEINT2 input is active (low). It is
cleared by returning nEINT2 to the passive (high) state.
EINT3
: External interrupt input 3. This interrupt will be active if the EINT3 input is active (high). It is
cleared by returning EINT3 to the passive (low) state.
TC1OI
: TC1 under flow interrupt. This interrupt becomes active on the next falling edge of the timer
counter 1 clock after the timer counter has under flowed (reached zero). It is cleared by writing to the
TC1EOI location.
1
2
3
4
5
6
7
8
Table 34. INTSR1
相關PDF資料 |
PDF描述 |
|---|---|
| EP7309 | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
| EP7309-CB-C | CONN MODULAR JACK 8-8 R/A UNSHLD |
| EP7309-CR-C | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
| EP7309-CV-C | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
| EP7309-ER-C | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EP7212-CV-D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EP7230 | 功能描述:電氣外殼配件 E-PANEL FITS 72 X 30 RoHS:否 制造商:Hammond Manufacturing 產品:Rack Accessories 類型: 面板寬度: 面板高度: 外部寬度: 外部高度: 外部深度: 顏色:Black |
| EP7236 | 功能描述:電氣外殼配件 E-PANEL FITS 72 X 36 RoHS:否 制造商:Hammond Manufacturing 產品:Rack Accessories 類型: 面板寬度: 面板高度: 外部寬度: 外部高度: 外部深度: 顏色:Black |
| EP7309 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
| EP7309_05 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:High-performance, Low-power, System-on-chip with Enhanced Digital Audio Interface |
發布緊急采購，3分鐘左右您將得到回復。