參數資料
型號： EP7211
廠商： Cirrus Logic, Inc.
英文描述： HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
中文描述： 高性能超低功耗系統與LCD控制器芯片
文件頁數： 105/166頁
文件大?。?/td> 2623K
代理商： EP7211
EP7211
High-Performance Ultra-Low-Power System-on-Chip with LCD Controller
105
Register Descriptions
DS352PP3
JUL 2001
5.8
CODR
—
The CODEC Interface Data Register
ADDRESS: 0x8000.0440
The CODR register is an 8-bit read/write register, to be used with the codec interface when this is
selected by the appropriate setting of Bit 0 (SERSEL) of the SYSCON2 register. Data written to or
read from this register is pushed or popped onto the appropriate 16-byte FIFO buffer. Data from this
buffer is then serialized and sent to or received from the codec sound device. When the codec is
enabled, the codec interrupt CSINT is generated repetitively at 1/8th of the byte transfer rate and the
state of the FIFOs can be read in the system flags register. The net data transfer rate to/from the codec
device is 8 kBps, giving an interrupt rate of 1 kHz.
5.9
UART Registers
5.9.1
UARTDR1
–
2 UART1
–
2 Data Registers
ADDRESS: 0x8000.0480 and 0x8000.1480
The UARTDR registers are 11-bit read and 8-bit write registers for all data transfers to or from the
internal UARTs 1 and 2.
Data written to these registers is pushed onto the 16-byte data TX holding FIFO if the FIFO is
enabled. If not it is stored in a one byte holding register. This write will initiate transmission from
the UART.
The UART data read registers are made up of the 8-bit data byte received from the UART together
with three bits of error status. Data read from this register is popped from the 16 byte data RX FIFO,
if the FIFO is enabled. If not it is read from a one byte buffer register containing the last byte received
by the UART. Data received and error status is automatically pushed onto the RX FIFO if it is
enabled. The RX FIFO is 10-bits wide by 16 deep.
NOTE:
These registers should be accessed as words
10
9
8
7:0
OVERR
PARERR
FRMERR
RX data
Bit
Description
8
FRMERR
: UART framing error. This bit is set if the UART detected a framing error while receiving the
associated data byte. Framing errors are caused by non-matching word lengths or bit rates.
9
PARERR
: UART parity error. This bit is set if the UART detected a parity error while receiving the data
byte.
10
OVERR
: UART over-run error. This bit is set if more data is received by the UART and the FIFO is full. The
overrun error bit is not associated with any single character, and so is not stored in the FIFO, if this bit is
set the entire contents of the FIFO is invalid and should be cleared. This error bit is cleared by reading the
UARTDR register.
相關PDF資料
PDF描述
EP7211-CP-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7212 HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CB-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
相關代理商/技術參數
參數描述
EP7211(208LQFP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC
EP7211(256PBGA) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC
EP7211-CB-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7211-CP-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*