- 您現在的位置：買賣IC網 > PDF目錄293745 > 1893YI-10 (INTEGRATED DEVICE TECHNOLOGY INC) DATACOM, INTERFACE CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | 1893YI-10 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, TQFP-64 |
| 文件頁數： | 148/152頁 |
| 文件大?。?/td> | 943K |
| 代理商： | 1893YI-10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁當前第148頁第149頁第150頁第151頁第152頁
Chapter 8
Management Register Set
ICS1893 Rev C 6/6/00
June, 2000
95
ICS1893 - Release
Copyright 2000, Integrated Circuit Systems, Inc.
All rights reserved.
8.12.8
Halt Symbol (bit 17.6)
The Halt Symbol bit indicates to an STA the detection of a Halt Symbol in a 100Base data stream by the
ICS1893.
During reception of a valid packet, the ICS1893 examines each symbol to ensure that the data being
passed to the MAC/Repeater Interface is error free. In addition, it looks for special symbols such as the Halt
Symbol. If a Halt Symbol is encountered, the ICS1893 indicates this condition to the MAC/repeater.
If this bit is set to a logic:
Zero, it indicates a Halt Symbol has not been detected since either the last read or reset of this register.
One, it indicates a Halt Symbol was detected in the packet since either the last read or reset of this
register.
This bit is a latching high bit. (For more information on latching high and latching low bits, see Section
8.1.4.1, “Latching High Bits”and Section 8.1.4.2, “Latching Low Bits”.)
Note:
This bit has no definition in 10Base-T mode.
8.12.9
Premature End (bit 17.5)
The Premature End bit indicates to an STA the detection of two consecutive Idles in a 100Base data
stream by the ICS1893.
During reception of a valid packet, the ICS1893 examines each symbol to ensure that the data being
passed to the MAC/Repeater Interface is error free. If two consecutive Idles are encountered, it indicates
this condition to the MAC/repeater by setting this bit.
If this bit is set to a logic:
Zero, it indicates a Premature End condition has not been detected since either the last read or reset of
this register.
One, it indicates a Premature End condition was detected in the packet since either the last read or reset
of this register.
This bit is a latching high bit. (For more information on latching high and latching low bits, see Section
8.1.4.1, “Latching High Bits”and Section 8.1.4.2, “Latching Low Bits”.)
Note:
This bit has no definition in 10Base-T mode.
8.12.10
Auto-Negotiation Complete (bit 17.4)
The Auto-Negotiation Complete bit is used to indicate to an STA the completion of the Auto-Negotiation
process. When this bit is set to logic:
Zero, it indicates that the auto-negotiation process is either not complete or is disabled by the Control
Register’s Auto-Negotiation Enable bit (bit 0.12)
One, it indicates that the ICS1893 has completed the auto-negotiation process and that the contents of
Management Registers 4, 5, and 6 are valid.
8.12.11
100Base-TX Signal Detect (bit 17.3)
The 100Base-TX Signal Detect bit indicates either the presence or absence of a signal on the Twisted-Pair
Receive pins (TP_RXP and TP_RXN) in 100Base-TX mode. This bit is logic:
Zero when no signal is detected on the Twisted-Pair Receive pins.
One when a signal is present on the Twisted-Pair Receive pins.
相關PDF資料 |
PDF描述 |
|---|---|
| 1894-40KLF | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1894-40KLFT | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1895230000 | 15 A, STRIP TERMINAL BLOCK, 2 ROWS, 2 DECKS |
| 18F-08P-241 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
| 18F-08P-244 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1893YI-10LF | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1893YI-10LFT | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1894 | 功能描述:支架與墊片 HEX .187X.625 ALUM RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 1894# | 制造商:Fluke Electronics 功能描述:BNC (F)/BANANA PLUG 制造商:Pomona Electronics 功能描述: |
| 1894 | 制造商:Pomona Electronics 功能描述:ADAPTER BNC FEMALE-BANANA PLUG 制造商:Pomona Electronics 功能描述:ADAPTER, BNC FEMALE-BANANA PLUG |
發布緊急采購，3分鐘左右您將得到回復。