- 您現在的位置：買賣IC網 > PDF目錄293745 > 1893YI-10 (INTEGRATED DEVICE TECHNOLOGY INC) DATACOM, INTERFACE CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | 1893YI-10 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, TQFP-64 |
| 文件頁數： | 141/152頁 |
| 文件大?。?/td> | 943K |
| 代理商： | 1893YI-10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁當前第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁
Chapter 8
Management Register Set
ICS1893 Rev C 6/6/00
June, 2000
89
ICS1893 - Release
Copyright 2000, Integrated Circuit Systems, Inc.
All rights reserved.
8.11.1
Command Override Write Enable (bit 16.15)
The Command Override Write Enable bit provides an STA the ability to alter the Command Override Write
(CW) bits located throughout the MII Register set. A two-step process is required to alter the value of a CW
bit:
1.
Step one is to issue a Command Override Write, (that is, set bit 16.15 to logic one). This step enables
the next MDIO write to have the ability to alter any CW bit.
2.
Step two is to write to the register that includes the CW bit which requires modification.
Note:
The Command Override Write Enable bit is a Self-Clearing bit that is automatically reset to logic
zero after the next MII write, thereby allowing only one subsequent write to alter the CW bits in a
single register. To alter additional CW bits, the Command Override Write Enable bit must once
again be set to logic one.
8.11.2
ICS Reserved (bits 16.14:11)
ICS is reserving these bits for future use. Functionally, these bits are equivalent to IEEE Reserved bits.
When one of these reserved bits is:
Read by an STA, the ICS1893 returns a logic zero.
Written to by an STA, the STA must use the default value specified in this data sheet.
ICS uses some reserved bits to invoke auxiliary functions. To ensure proper operation of the ICS1893, an
STA must maintain the default value of these bits. Therefore, ICS recommends that an STA always write
the default value of any reserved bits during all management register write operations.
8.11.3
PHY Address (bits 16.10:6)
These five bits hold the Serial Management Port Address of the ICS1893. During either a hardware reset
or a power-on reset, the PHY address is read from the LED interface. (For information on the LED
interface, see Section 6.8, “Status Interface”and Section 9.3.2, “Multi-Function (Multiplexed) Pins: PHY
Address and LED Pins”). The PHY address is then latched into this register. (The value of each of the PHY
Address bits is unaffected by a software reset.)
8.11.4
Stream Cipher Scrambler Test Mode (bit 16.5)
The Stream Cipher Scrambler Test Mode bit is used to force the ICS1893 to lose LOCK, thereby requiring
the Stream Cipher Scrambler to resynchronize.
8.11.5
ICS Reserved (bit 16.4)
See Section 8.11.2, “ICS Reserved (bits 16.14:11)”, the text for which also applies here.
8.11.6
NRZ/NRZI Encoding (bit 16.3)
This bit allows an STA to control whether NRZ (Not Return to Zero) or NRZI (Not Return to Zero, Invert on
One) encoding is applied to the serial transmit data stream in 100Base-TX mode. When this bit is logic:
Zero, the ICS1893 encodes the serial transmit data stream using NRZ encoding.
One, the ICS1893 encodes the serial transmit data stream using NRZI encoding.
相關PDF資料 |
PDF描述 |
|---|---|
| 1894-40KLF | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1894-40KLFT | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1895230000 | 15 A, STRIP TERMINAL BLOCK, 2 ROWS, 2 DECKS |
| 18F-08P-241 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
| 18F-08P-244 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1893YI-10LF | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1893YI-10LFT | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1894 | 功能描述:支架與墊片 HEX .187X.625 ALUM RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 1894# | 制造商:Fluke Electronics 功能描述:BNC (F)/BANANA PLUG 制造商:Pomona Electronics 功能描述: |
| 1894 | 制造商:Pomona Electronics 功能描述:ADAPTER BNC FEMALE-BANANA PLUG 制造商:Pomona Electronics 功能描述:ADAPTER, BNC FEMALE-BANANA PLUG |
發布緊急采購，3分鐘左右您將得到回復。