- 您現在的位置：買賣IC網 > PDF目錄293745 > 1893YI-10 (INTEGRATED DEVICE TECHNOLOGY INC) DATACOM, INTERFACE CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | 1893YI-10 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 網絡接口 |
| 英文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, TQFP-64 |
| 文件頁數： | 116/152頁 |
| 文件大小： | 943K |
| 代理商： | 1893YI-10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁當前第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁
ICS1893 Rev C 6/6/00
June, 2000
66
Chapter 8
Management Register Set
ICS1893 Data Sheet - Release
Copyright 2000, Integrated Circuit Systems, Inc.
All rights reserved.
8.2.8
Duplex Mode (bit 0.8)
This bit provides a means of controlling the ICS1893 Duplex Mode. Its operation depends on several other
functions, including the HW/SW input pin and the Auto-Negotiation Enable bit (bit 0.12). When the ICS1893
is configured for:
Hardware mode (that is, the HW/SW pin is logic zero), the ICS1893 isolates bit 0.8 and uses the
DPXSEL input pin to establish the Duplex mode for the ICS1893. In this Hardware mode:
– Bit 0.8 is undefined.
– The ICS1893 provides a Duplex Mode Status bit (in the QuickPoll Detailed Status Register, bit
17.14), which always shows the setting of an active link.
Software mode (that is, the HW/SW pin is logic one), the function of bit 0.8 depends on the
Auto-Negotiation Enable bit, 0.12. When the auto-negotiation process is:
– Enabled, the ICS1893 isolates bit 0.8 and relies upon the results of the auto-negotiation process to
establish the duplex mode.
– Disabled, bit 0.8 determines the Duplex mode. Setting bit 0.8 to logic:
Zero selects half-duplex operations.
One selects full-duplex operations. (When the ICS1893 is operating in Loopback mode, it isolates
bit 0.8, which has no effect on the operation of the ICS1893.)
8.2.9
Collision Test (bit 0.7)
This bit controls the ICS1893 Collision Test function. When an STA sets bit 0.7 to logic:
Zero, the ICS1893 disables the collision detection circuitry for the Collision Test function. In this case, the
COL signal does not track the TXEN signal. (The default value for this bit is logic zero, that is, disabled.)
One, as per the ISO/IEE 8802-3 standard, clause 22.2.4.1.9, the ICS1893 enables the collision detection
circuitry for the Collision Test function, even if the ICS1893 is in Loopback mode (that is, bit 0.14 is set to
1). In this case, the Collision Test function tracks the Collision Detect signal (COL) in response to the
TXEN signal. The ICS1893 asserts the Collision signal (COL) within 512 bit times of receiving an
asserted TXEN signal, and it de-asserts COL within 4 bit times of the de-assertion of the TXEN signal.
8.2.10
IEEE Reserved Bits (bits 0.6:0)
The IEEE reserves these bits for future use. When an STA:
Reads a reserved bit, the ICS1893 returns a logic zero.
Writes to a reserved bit, it must use the default value specified in this data sheet.
The ICS1893 uses some reserved bits to invoke auxiliary functions. To ensure proper operation of the
ICS1893, an STA must maintain the default value of these bits. Therefore, ICS recommends that during
any STA write operation, an STA write the default value to all reserved bits, even those bits that are Read
Only.
相關PDF資料 |
PDF描述 |
|---|---|
| 1894-40KLF | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1894-40KLFT | DATACOM, INTERFACE CIRCUIT, QCC40 |
| 1895230000 | 15 A, STRIP TERMINAL BLOCK, 2 ROWS, 2 DECKS |
| 18F-08P-241 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
| 18F-08P-244 | 8 CONTACT(S), CABLE MOUNT, MINI DIN CONNECTOR, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1893YI-10LF | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1893YI-10LFT | 功能描述:以太網 IC 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| 1894 | 功能描述:支架與墊片 HEX .187X.625 ALUM RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 1894# | 制造商:Fluke Electronics 功能描述:BNC (F)/BANANA PLUG 制造商:Pomona Electronics 功能描述: |
| 1894 | 制造商:Pomona Electronics 功能描述:ADAPTER BNC FEMALE-BANANA PLUG 制造商:Pomona Electronics 功能描述:ADAPTER, BNC FEMALE-BANANA PLUG |
發布緊急采購，3分鐘左右您將得到回復。