參數資料
型號： SP37E760
廠商： SMSC Corporation
英文描述： 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
中文描述： 3.3第VI / O控制器為嵌入式應用
文件頁數： 55/78頁
文件大小： 510K
代理商： SP37E760
7.3.25 CR1E
(Reserved). The default value of this register after power up is 80H.
SMSC DS – SP37E760
Page 55
Rev. 04/13/2001
7.3.26 CR1F
(Reserved). The default value of this register after power up is 00H.
7.3.27 CR20
(Reserved). The default value of this register after power up is 3CH.
7.3.28 CR21 - CR22
Registers CR21 - CR22 are Reserved. Reserved bits cannot be written and return 0 when read.
7.3.29 CR23
CR23 can only be accessed in the configuration state and after the CSR has been initialized to 23H. The default
value of this register after power up is 00H (Table 41). CR23 is used to select the base address of the parallel port.
If EPP is not enabled, the parallel port can be set to 192 locations on 4-byte boundaries from 100H - 3FCH; if EPP is
enabled, the parallel port can be set to 96 locations on 8-byte boundaries from 100H - 3F8H (Table 42). To disable
the parallel port, set ADR9 and ADR8 to zero.
Parallel Port Address Decoding: nCS = ’0’ and A10 = ’0’ are required to access the Parallel Port when in Compatible,
Bi-directional, or EPP modes. A10 is active when in ECP mode.
Table 41 - CR23: Parallel Port Base Address Register
DB7
DB6
DB5
DB4
ADR9
ADR8
ADR7
ADR6
Table 42 - Parallel Port Addressing Options
EPP ENABLED
ADDRESSING (LOW BITS) DECODE
No
A[1:0] = XXb
Yes
A[2:0] = XXXb
DB3
ADR5
DB2
ADR4
DB1
ADR3
DB0
ADR2
7.3.30 CR24
CR24 can only be accessed in the configuration state and after the CSR has been initialized to 24H. The default
value of this register after power up is 00H (Table 43). CR24 is used to select the base address of Serial Port 1
(UART1). The serial port can be set to 96 locations on 8-byte boundaries from 100H - 3F8H. To disable Serial Port
1, set ADR9 and ADR8 to zero. Set CR24.0 to 0 when writing the UART1 Base Address.
Serial Port 1 Address Decoding: nCS = ’0’ and A10 = ’0’ are required to access UART1 registers. A[
2
:0] are decoded
as XXXb.
Table 43 - CR24: UART1 Base Address Register
DB7
DB6
DB5
DB4
ADR9
ADR8
ADR7
ADR6
DB3
ADR5
DB2
ADR4
DB1
ADR3
DB0
0
7.3.31 CR25
CR25 can only be accessed in the configuration state and after the CSR has been initialized to 25H. The default
value of this register after power up is 00H (Table 44). CR25 is used to select the base address of Serial Port 2
(UART2). Serial Port 2 can be set to 96 locations on 8-byte boundaries from 100H - 3F8H. To disable Serial Port 2,
set ADR9 and ADR8 to zero. Set CR25.0 to 0 when writing the UART2 Base Address.
Serial Port 2 Address Decoding: nCS = ’0’ and A10 = ’0’ are required to access UART2 registers. A[
2
:0] are decoded
as XXXb.
相關PDF資料
PDF描述
SP37E760-MC 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP8720 ECL two-modulus divider, with ECL10K compatible outputs
SP8720ADG ECL two-modulus divider, with ECL10K compatible outputs
SP8720BDG ECL two-modulus divider, with ECL10K compatible outputs
SPF5001 Surface-mount 4-circuit Low-side Switch Array
相關代理商/技術參數
參數描述
SP37E760-MC 制造商:SMSC 制造商全稱:SMSC 功能描述:3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP37E760-MD 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37E760-MT 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37R0FL 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor
SP38 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*