- 您現在的位置：買賣IC網 > PDF目錄365670 > SP37E760 (SMSC Corporation) 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS PDF資料下載
參數資料
| 型號： | SP37E760 |
| 廠商： | SMSC Corporation |
| 英文描述： | 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS |
| 中文描述： | 3.3第VI / O控制器為嵌入式應用 |
| 文件頁數： | 30/78頁 |
| 文件大?。?/td> | 510K |
| 代理商： | SP37E760 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
5.1.7
ADDRESS OFFSET = 06H
The EPP Data Port 2 is located at an offset of ‘06H’ from the base address. Refer to EPP DATA PORT 0 for a
description of operation. This register is only available in EPP mode.
SMSC DS – SP37E760
Page 30
Rev. 04/13/2001
EPP DATA PORT 2
5.1.8
ADDRESS OFFSET = 07H
The EPP Data Port 3 is located at an offset of ‘07H’ from the base address. Refer to EPP DATA PORT 0 for a
description of operation. This register is only available in EPP mode.
EPP DATA PORT 3
5.2 EPP 1.9 OPERATION
When the EPP mode is selected in the configuration register, the standard and bi-directional modes are also
available. If no EPP Read, Write or Address cycle is currently executing, then the PDx bus is in the standard or bi-
directional mode, and all output signals (STROBE, AUTOFD, INIT) are as set by the SPP Control Port and direction is
controlled by PCD of the Control port.
In EPP mode, the system timing is closely coupled to the EPP timing. For this reason, a watchdog timer is required to
prevent system lockup. The timer indicates if more than 10
μ
sec have elapsed from the start of the EPP cycle (nIOR
or nIOW asserted) to nWAIT being deasserted (after command). If a time-out occurs, the current EPP cycle is
aborted and the time-out condition is indicated in Status bit 0.
During an EPP cycle, if STROBE is active, it overrides the EPP write signal forcing the PDx bus to always be in a
write mode and the nWRITE signal to always be asserted.
5.2.1
Before an EPP cycle is executed, the software must ensure that the control register bit PCD is a logic “0” (i.e. a 04H
or 05H should be written to the Control port). If the user leaves PCD as a logic “1”, and attempts to perform an EPP
write, the chip is unable to perform the write (because PCD is a logic “1”) and will appear to perform an EPP read on
the parallel bus, no error is indicated.
5.2.2
EPP 1.9 WRITE
The timing for a write operation (address or data) is shown in timing diagram EPP 1.9 Write Data or Address cycle.
IOCHRDY is driven active low at the start of each EPP write and is released when it has been determined that the
write cycle can complete. The write cycle can complete under the following circumstances:
1. If the EPP bus is not ready (nWAIT is active low) when nDATASTB or nADDRSTB goes active then the write
can complete when nWAIT goes inactive high.
2. If the EPP bus is ready (nWAIT is inactive high) then the chip must wait for it to go active low before changing
the state of nDATASTB, nWRITE or nADDRSTB. The write can complete once nWAIT is determined inactive.
Write Sequence of operation
1. The host selects an EPP register, places data on the SData bus and drives nIOW active.
2. The chip drives IOCHRDY inactive (low).
3. If WAIT is not asserted, the chip must wait until WAIT is asserted.
4. The chip places address or data on PData bus, clears PDIR, and asserts nWRITE.
5. Chip asserts nDATASTB or nADDRSTRB indicating that PData bus contains valid information, and the WRITE
signal is valid.
6. Peripheral deasserts nWAIT, indicating that any setup requirements have been satisfied and the chip may begin
the termination phase of the cycle.
7. A) The chip deasserts nDATASTB or nADDRSTRB, this marks the beginning of the termination phase.
If it has not already done so, the peripheral should latch the information byte now.
B) The chip latches the data from the SData bus for the PData bus and asserts (releases) IOCHRDY allowing
the host to complete the write cycle.
8. Peripheral asserts nWAIT, indicating to the host that any hold time requirements have been satisfied and
acknowledging the termination of the cycle.
9. Chip may modify nWRITE and nPDATA in preparation for the next cycle.
SOFTWARE CONSTRAINTS
相關PDF資料 |
PDF描述 |
|---|---|
| SP37E760-MC | 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS |
| SP8720 | ECL two-modulus divider, with ECL10K compatible outputs |
| SP8720ADG | ECL two-modulus divider, with ECL10K compatible outputs |
| SP8720BDG | ECL two-modulus divider, with ECL10K compatible outputs |
| SPF5001 | Surface-mount 4-circuit Low-side Switch Array |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP37E760-MC | 制造商:SMSC 制造商全稱:SMSC 功能描述:3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS |
| SP37E760-MD | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| SP37E760-MT | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| SP37R0FL | 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor |
| SP38 | 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH |
發布緊急采購，3分鐘左右您將得到回復。