參數資料
型號： SP37E760
廠商： SMSC Corporation
英文描述： 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
中文描述： 3.3第VI / O控制器為嵌入式應用
文件頁數： 45/78頁
文件大小： 510K
代理商： SP37E760
SMSC DS – SP37E760
Page 45
Rev. 04/13/2001
7
The configuration of the SP37E760 is programmed through hardware selectable Configuration Access Ports that
appear when the chip is placed into the configuration state. The SP37E760 logical device blocks, if enabled, will
operate normally in the configuration state.
CONFIGURATION
7.1 Configuration Access Ports
The Configuration Access Ports are the CONFIG PORT, the INDEX PORT, and the DATA PORT (Table 23). The
base address of these registers is controlled by the nRTS2/SYSOPT pin (see Table 1). To determine the
configuration base address, the state of the nRTS2/SYSOPT pin is latched by the falling edge of a hardware reset. If
the latched state is a 0, the base address of the Configuration Access Ports is located at address 3F0H; if the latched
state is a 1, the base address is located at address 370H.
Table 23 - Configuration Access Ports
PORT NAME
SYSOPT = 0
CONFIG PORT
0x3F0
INDEX PORT
0x3F0
DATA PORT
INDEX PORT + 1
Note
1
:
The INDEX and DATA ports are active only when the SP37E760 is in the configuration state.
Note
2
:
The INDEX PORT is only readable in the configuration state.
SYSOPT = 1
0x370
0x370
TYPE
WRITE
READ/WRITE
1,2
READ/WRITE
1
7.2 Configuration State
The configuration registers are used to select programmable chip options. The SP37E760 operates in two possible
states: the run state and the configuration state. After power up by default the chip is in the run state. To program
the configuration registers, the configuration state must be explicitly enabled. Programming the configuration
registers typically follows this sequence:
1. Enter the Configuration State,
2. Program the Configuration Register(s),
3. Exit the Configuration State.
7.2.1
To enter the configuration state write the Configuration Access Key to the CONFIG PORT. The Configuration Access
Key is one byte of 55H data. The SP37E760 will automatically activate the Configuration Access Ports following this
procedure.
ENTERING THE CONFIGURATION STATE
7.2.2
The SP37E760 contains configuration registers CR00-CR2F. After the SP37E760 enters the configuration state,
configuration registers can be programmed by first writing the register index number (00 - 2FH) to the Configuration
Select Register (CSR) through the INDEX PORT and then writing or reading the configuration register contents
through the DATA PORT. Configuration register access remains enabled until the configuration state is explicitly
exited.
CONFIGURATION REGISTER PROGRAMMING
7.2.3
To exit the configuration state, write one byte of AAH data to the CONFIG PORT. The SP37E760 will automatically
deactivate the Configuration Access Ports following this procedure, at which point configuration register access
cannot occur until the configuration state is explicitly re-enabled.
EXITING THE CONFIGURATION STATE
相關PDF資料
PDF描述
SP37E760-MC 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP8720 ECL two-modulus divider, with ECL10K compatible outputs
SP8720ADG ECL two-modulus divider, with ECL10K compatible outputs
SP8720BDG ECL two-modulus divider, with ECL10K compatible outputs
SPF5001 Surface-mount 4-circuit Low-side Switch Array
相關代理商/技術參數
參數描述
SP37E760-MC 制造商:SMSC 制造商全稱:SMSC 功能描述:3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
SP37E760-MD 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37E760-MT 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37R0FL 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor
SP38 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*