- 您現在的位置：買賣IC網 > PDF目錄365566 > SiI3114 (Silicon Image, Inc.) PCI to Serial ATA Controller PDF資料下載
參數資料
| 型號： | SiI3114 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to Serial ATA Controller |
| 中文描述： | PCI到Serial ATA控制器 |
| 文件頁數： | 92/127頁 |
| 文件大?。?/td> | 598K |
| 代理商： | SII3114 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
SiI
3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
If enabled, a PMACK will be sent to the device; if not enabled, a PMNAK will be sent. When the request is
received and its acknowledgement is enabled, Slumber mode is entered.
SiI
-DS-0103-D
84
2007 Silicon Image, Inc.
Slumber mode status is reported in both the SStatus register (‘0110’ in the IPM field) and the SMisc register (bit
5).
Slumber mode is cleared by setting the ComWake bit in the Smisc register. This will send a COMWAKE signal to
the device through the Serial ATA link to initiate a Slumber to On sequence. Slumber mode can also be cleared
through receipt of OOB signals from the device.
Hot Plug Support
The state diagram below illustrates the logic to support Hot Plugging.
CR
PhyRdy
Periodically send ComReset
until ComInit received
Normal operation
go_to_CR
dp_phyrdy=0
dp_phyrdy=1
Figure 10. Hot Plug Logic State Diagram
The
go_to_CR
signal is generated by a timer if the internal logic fails to detect valid signals from the Serial ATA
wire for 200 ns. Logic behavior is as follows:
1. Initial power-up – A ComReset is generated during initial power up. If a device is present and operational,
the PhyRdy state will be entered. If a device is not present or not responding, the CR state will be entered
and ComReset will be generated every 100 ms.
2. Device is unplugged – The internal logic detects that no more signal is present on the Serial ATA wire.
The timer will expire after 200 ns and
go_to_CR
will be asserted; the CR state will be entered and
ComReset will be generated every 100 ms. The internal PHYRDY signal will go false causing an interrupt
to the host driver (PHYRDY change interrupt, bit 16 of SError register; enabled by bit 16 of SIEN register).
3. Device is plugged in – The device will respond to the ComReset with a ComInit. Normal operation will
commence and the internal logic will detect a PHYRDY signal going true causing an interrupt to the host
driver (PHYRDY change interrupt, bit 16 of SError register; enabled by bit 16 of SIEN register).
相關PDF資料 |
PDF描述 |
|---|---|
| SII3114_07 | PCI to Serial ATA Controller |
| SiI3114CT176 | PCI to Serial ATA Controller |
| SiI3114CTU | PCI to Serial ATA Controller |
| SII3124A | PCI-X to Serial ATA Controller |
| SiI3124ACBHU | PCI-X to Serial ATA Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3114_07 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller |
| SII3114CT176 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller |
| SII3114CTU | 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述: |
| SII3124A | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3124ACBHU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
發布緊急采購，3分鐘左右您將得到回復。