- 您現在的位置：買賣IC網 > PDF目錄365566 > SiI3114 (Silicon Image, Inc.) PCI to Serial ATA Controller PDF資料下載
參數資料
| 型號： | SiI3114 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to Serial ATA Controller |
| 中文描述： | PCI到Serial ATA控制器 |
| 文件頁數： | 89/127頁 |
| 文件大小： | 598K |
| 代理商： | SII3114 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
SiI
3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
with one additional step. Before the DMA is enabled, the Channel x Virtual DMA/PIO Read Ahead Byte
Count register must be written with the 32-bit count of the number of bytes to be transferred.
2007 Silicon Image, Inc.
81
SiI
-DS-0103-D
Wait for a PCI interrupt.
Read the DMA status bits [18:16] of the PCI Bus Master – Channel x register, and check that bit 18 is set
to make sure the interrupt was generated by the expected channel.
If expected channel interrupted, read bits [11:10] of the Channel x Task File Timing + Configuration +
Status register to determine the cause of the interrupt. Bit 11 is set if the ATA/ATAPI device has an
interrupt pending, bit 10 is set if a virtual DMA operation completed.
If a virtual DMA operation completed,
Write 00
H
to bits [7:0] of the PCI Bus Master – Channel x register to disable DMA operation.
Write 1 to bits [18:17] of the PCI Bus Master –Channel x register to reset the DMA status and
virtual DMA interrupt bits, and PCI interrupt.
Check the previously read DMA status bits to ensure the DMA completed successfully.
Because ATA/ATAPI commands that transfer data using PIO can generate several interrupts
during the data transfer phase of the command, a race condition is created between the interrupt
indicating the completion of a virtual DMA operation, and the interrupt from the ATA/ATAPI device
indicating it is ready to perform the next part of the data transfer. To prevent missing an
ATA/ATAPI device interrupt due to this race condition, it is necessary to re-read the Channel x
Task File Timing + Configuration + Status register after disabling DMA operation and examining
bit 11. If bit 11 is set, the ATA/ATAPI device is interrupting and should be serviced by following the
steps below (assuming that the virtual DMA operation completed successfully).
If the ATA/ATAPI device has interrupted,
Read the device status at bits [31:24] in the Channel x Task File Register 1 register to clear the
device interrupt and determine if there was an error.
Write 1 to bit 18 of the PCI Bus Master – Channel x register to clear the DMA Complete bit
(NOTE: The DMA Complete bit acts as a latched copy of the ATA interrupt line when the channel
is not performing a DMA operation).
If the ATA/ATAPI device is not reporting an error, and DRQ is asserted (bit 27 of Channel x Task
File Register 1), then the device is interrupting to transfer data to the device. To transfer the data,
the DMA registers are setup to only perform that part of the data transfer expected for this
interrupt. The DMA is setup similarly to the way it is when performing a normal write DMA
command, but with one additional step. Before the DMA is enabled, the Channel x Virtual
DMA/PIO Read Ahead Byte Count register must be written with the 32-bit count of the number of
bytes to be transferred for this interrupt.
Repeat the above steps starting at “Wait for PCI interrupt” until all data for the write command has been
transferred or an error has been detected.
Using Virtual DMA with DMA Capable Devices
Even though a device may be DMA capable, there are ATA/ATAPI commands that require that a PIO mode be
used to transfer data. For these commands, virtual DMA can be used to perform the data transfer. Using virtual
DMA with an ATA/ATAPI device that has already been configured to use DMA for normal read/write operation is
performed very much like the sequence described above for PIO mode only devices, but with the following
additional consideration: The Data Transfer Mode – Channel x register associated with the ATA/ATAPI device
needs to be programmed for a PIO type transfer mode
before
DMA operation is enabled, and must be re-
programmed with the DMA/UDMA transfer type used during normal DMA operation once the virtual DMA
operation is complete.
相關PDF資料 |
PDF描述 |
|---|---|
| SII3114_07 | PCI to Serial ATA Controller |
| SiI3114CT176 | PCI to Serial ATA Controller |
| SiI3114CTU | PCI to Serial ATA Controller |
| SII3124A | PCI-X to Serial ATA Controller |
| SiI3124ACBHU | PCI-X to Serial ATA Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3114_07 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller |
| SII3114CT176 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller |
| SII3114CTU | 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述: |
| SII3124A | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3124ACBHU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
發布緊急采購，3分鐘左右您將得到回復。