參數資料
型號： SiI3114
廠商： Silicon Image, Inc.
英文描述： PCI to Serial ATA Controller
中文描述： PCI到Serial ATA控制器
文件頁數： 125/127頁
文件大?。?/td> 598K
代理商： SII3114
SiI
3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
Flash and EEPROM Programming Sequences
Flash Memory Access
2007 Silicon Image, Inc.
117
SiI
-DS-0103-D
The
SiI
3114 supports an external flash memory device up to 4 Mbit in capacity. Access to the Flash memory is
available through two means: PCI Direct Access and Register Access.
PCI Direct Access
Access to the Expansion Rom is enabled by setting bit 0 in the Expansion Rom Base Address register at Offset
30h of the PCI Configuration Space. When this bit is set, bits [31:19] of the same register are programmable by
the system to set the base address for all Flash memory accesses. Read and write operations with the flash
memory are initiated by Memory Read and Memory Write commands on the PCI bus. Accesses may be as bytes,
words, or dwords.
Register Access
This type of flash memory access is carried out through a sequence of internal register read and write operations.
The proper programming sequences are detailed below.
Flash Write Operation
Verify that bit 25 is cleared in the register at Offset 50H of Base Address 5. The bit reads one when a
memory access is currently in progress.
It reads zero when the memory access is complete and ready for another operation.
Program the write address for the Flash memory access. The address field is defined by bits [18:00] in
the Flash Memory Address – Command + Status register.
Program the write data for the Flash memory access. The data field is defined by bits [07:00] in the Flash
Memory Data register at Offset 54 of Base Address 5.
Program the memory access type. The memory access type is defined by bit 24 in the Flash Memory
Address – Command + Status register. The bit must be cleared for a memory write access.
Initiate the Flash memory access by setting bit 25 in the Flash Memory Address – Command + Status
register.
Flash Read Operation
Verify that bit 25 is cleared in the Flash Memory Address – Command + Status register at Offset 50
H
of
Base Address 5. The bit reads one when a memory access is currently in progress. It reads zero when
the memory access is complete and ready for another operation.
Program the read address for the Flash memory access. The address field is defined by bits [18:00] in
the Flash Memory Address – Command + Status register.
Program the memory access type. The memory access type is defined by bit 24 in the Flash Memory
Address – Command + Status register. The bit must be set for a memory read access.
Initiate the Flash memory access by setting bit 25 in the Flash Memory Address – Command + Status
register.
Verify that bit 25 is cleared in the Flash Memory Address – Command + Status register. The bit reads one
when a memory access is currently in progress. It reads zero when the memory access is complete.
Read the data from the Flash memory access. The data field is defined by bits [07:00] in the Flash
Memory Data register at Offset 54
H
of Base Address 5.
相關PDF資料
PDF描述
SII3114_07 PCI to Serial ATA Controller
SiI3114CT176 PCI to Serial ATA Controller
SiI3114CTU PCI to Serial ATA Controller
SII3124A PCI-X to Serial ATA Controller
SiI3124ACBHU PCI-X to Serial ATA Controller
相關代理商/技術參數
參數描述
SII3114_07 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller
SII3114CT176 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller
SII3114CTU 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述:
SII3124A 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller
SII3124ACBHU 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*