參數資料
型號： SC16C752IB48,157
廠商： NXP Semiconductors
文件頁數： 45/47頁
文件大?。?/td> 0K
描述： IC DUAL UART 64BYTE 48LQFP
標準包裝： 1,250
通道數： 2，DUART
FIFO's： 64 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
其它名稱： 935270055157
SC16C752IB48
SC16C752IB48-ND
Philips Semiconductors
SC16C752
Dual UART with 64-byte FIFO
Product data
Rev. 04 — 20 June 2003
7 of 47
9397 750 11635
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
The SC16C752 has selectable hardware ow control and software ow control.
Hardware ow control signicantly reduces software overhead and increases system
efciency by automatically controlling serial data ow using the RTS output and CTS
input signals. Software ow control automatically controls data ow by using
programmable Xon/Xoff characters.
The UART includes a programmable baud rate generator that can divide the timing
reference clock input by a divisor between 1 and (216
1).
6.1 Trigger levels
The SC16C752 provides independent selectable and programmable trigger levels for
both receiver and transmitter DMA and interrupt generation. After reset, both
transmitter and receiver FIFOs are disabled and so, in effect, the trigger level is the
default value of one byte. The selectable trigger levels are available via the FCR. The
programmable trigger levels are available via the TLR.
6.2 Hardware ow control
Hardware ow control is comprised of Auto-CTS and Auto-RTS. Auto-CTS and
Auto-RTS can be enabled/disabled independently by programming EFR[7:6].
With Auto-CTS, CTS must be active before the UART can transmit data.
Auto-RTS only activates the RTS output when there is enough room in the FIFO to
receive data and de-activates the RTS output when the RX FIFO is sufciently full.
The halt and resume trigger levels in the TCR determine the levels at which RTS is
activated/deactivated.
If both Auto-CTS and Auto-RTS are enabled, when RTS is connected to CTS, data
transmission does not occur unless the receiver FIFO has empty space. Thus,
overrun errors are eliminated during hardware ow control. If not enabled, overrun
errors occur if the transmit data rate exceeds the receive FIFO servicing latency.
Fig 3.
Autoow control (Auto-RTS and Auto-CTS) example.
RX
FIFO
SERIAL-TO-
PARALLEL
FLOW
CONTROL
TX
FIFO
PARALLEL-
TO-SERIAL
FLOW
CONTROL
PARALLEL-
TO-SERIAL
FLOW
CONTROL
SERIAL-TO-
PARALLEL
FLOW
TX
FIFO
RX
FIFO
UART 1
UART 2
D7-D0
RX
TX
RTS
CTS
TX
RX
CTS
RTS
D7-D0
CONTROL
002aaa228
相關PDF資料
PDF描述
ATMEGA1284P-AUR MCU AVR 128KB FLASH 20MHZ 44TQFP
ATMEGA1284P-MUR MCU AVR 128KB FLASH 20MHZ 44VQFN
AT89C51RB2-SLRUM MCU 8051 16K FLASH 5V 44-PLCC
AT89C51RB2-SLRUL MCU 8051 16K FLASH 3V 44-PLCC
MS27484E14B18S CONN PLUG 18POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
SC16C754 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO
SC16C754B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
SC16C754BIA68 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,518 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*