- 您現在的位置：買賣IC網 > PDF目錄11812 > SC16C752IB48,157 (NXP Semiconductors)IC DUAL UART 64BYTE 48LQFP PDF資料下載
參數資料
| 型號： | SC16C752IB48,157 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 44/47頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DUAL UART 64BYTE 48LQFP |
| 標準包裝： | 1,250 |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 935270055157 SC16C752IB48 SC16C752IB48-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁
Philips Semiconductors
SC16C752
Dual UART with 64-byte FIFO
Product data
Rev. 04 — 20 June 2003
6 of 47
9397 750 11635
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.
Functional description
The SC16C752 UART is pin-compatible with the SC16C2550 UART. It provides more
enhanced features. All additional features are provided through a special enhanced
feature register.
The UART will perform serial-to-parallel conversion on data characters received from
peripheral devices or modems, and parallel-to-parallel conversion on data characters
transmitted by the processor. The complete status of each channel of the SC16C752
UART can be read at any time during functional operation by the processor.
The SC16C752 can be placed in an alternate mode (FIFO mode) relieving the
processor of excessive software overhead by buffering received/transmitted
characters. Both the receiver and transmitter FIFOs can store up to 64 bytes
(including three additional bits of error status per byte for the receiver FIFO) and have
selectable or programmable trigger levels. Primary outputs RXRDY and TXRDY allow
signalling of DMA transfers.
RTSA, RTSB
33, 22
O
Request to Send (Active-LOW). These outputs are associated with individual UART
channels, A and B. A logic 0 on the RTS pin indicates the transmitter has data ready
and waiting to send. Writing a logic 1 in the modem control register MCR[1] will set this
pin to a logic 0, indicating data is available. After a reset these pins are set to a logic 1.
These pins only affect the transmit and receive operations when Auto-RTS function is
enabled via the Enhanced Feature Register (EFR[6]) for hardware ow control
operation.
RXA, RXB
5, 4
I
Receive data input. These inputs are associated with individual serial channel data to
the SC16C752. During the local loop-back mode, these RX input pins are disabled
and TX data is connected to the UART RX input internally.
RXRDYA,
RXRDYB
31, 18
O
Receive Ready (Active-LOW). RXRDYA or RXRDYB goes LOW when the trigger
level has been reached or the FIFO has at least one character. It goes HIGH when the
RX FIFO is empty.
TXA, TXB
7, 8
O
Transmit data A, B. These outputs are associated with individual serial transmit
channel data from the SC16C752. During the local loop-back mode, the TX output pin
is disabled and TX data is internally connected to the UART RX input.
TXRDYA,
TXRDYB
43, 6
O
Transmit Ready (Active-LOW). TXRDYAor TXRDYB go LOW when there are at least
a trigger level number of spaces available or when the FIFO is empty. It goes HIGH
when the FIFO is full or not empty.
VCC
42
I
Power supply input.
XTAL1
13
I
Crystal or external clock input. Functions as a crystal input or as an external clock
input. A crystal can be connected between XTAL1 and XTAL2 to form an internal
oscillator circuit (see Figure 12). Alternatively, an external clock can be connected to
this pin to provide custom data rates.
XTAL2
14
O
Output of the crystal oscillator or buffered clock. (See also XTAL1.) XTAL2 is used
as a crystal oscillator output or a buffered clock output.
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA1284P-AUR | MCU AVR 128KB FLASH 20MHZ 44TQFP |
| ATMEGA1284P-MUR | MCU AVR 128KB FLASH 20MHZ 44VQFN |
| AT89C51RB2-SLRUM | MCU 8051 16K FLASH 5V 44-PLCC |
| AT89C51RB2-SLRUL | MCU 8051 16K FLASH 3V 44-PLCC |
| MS27484E14B18S | CONN PLUG 18POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C754 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO |
| SC16C754B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC16C754BIA68 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,518 | 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。