- 您現在的位置：買賣IC網 > PDF目錄365460 > S71WS512NC0BFWY63 (Spansion Inc.) Stacked Multi-Chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71WS512NC0BFWY63 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 51/188頁 |
| 文件大?。?/td> | 2252K |
| 代理商： | S71WS512NC0BFWY63 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁
September 15, 2005 S71WS-N_01_A4
S71WS-Nx0 Based MCPs
49
A d v a n c e I n f o r m a t i o n
DQ6: Toggle Bit I .
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algo-
rithm is in progress or complete, or whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address in the same bank, and is valid after the rising edge of
the final WE# pulse in the command sequence (prior to the program or erase operation), and dur-
ing the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any ad-
dress cause DQ6 to toggle. When the operation is complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6
toggles for approximately t
ASP
[all sectors protected toggle time], then returns to reading array
data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unpro-
tected sectors, and ignores the selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or
is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm
is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops tog-
gling. However, the system must also use DQ2 to determine which sectors are erasing or erase-
suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector, DQ6 toggles for approximately t
PAP
after the
program command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embed-
ded Program Algorithm is complete.
See the following for additional information:
Figure 10.6
,
Write Operation Status Flowchart
;
Figure 14.18
,
Toggle Bit Timings (During Embedded Algorithm)
, and
Table 10.20
.
Toggle Bit I on DQ6 requires either OE# or CE# to be de-asserted and reasserted to show the
change in state.
DQ2: Toggle Bit I I .
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a par-
ticular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether
that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse
in the command sequence. DQ2 toggles when the system reads at addresses within those sectors
that have been selected for erasure. But DQ2 cannot distinguish whether the sector is actively
erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus,
both status bits are required for sector and mode information. Refer to
Table 14.10
to compare
outputs for DQ2 and DQ6. See the following for additional information:
Figure 10.6
, the “DQ6:
Toggle Bit I” section, and
Figures
14.17
–
14.20
.
Reading Toggle Bits DQ6/ DQ2.
Whenever the system initially begins reading toggle bit status,
it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typ-
ically, the system would note and store the value of the toggle bit after the first read. After the
second read, the system would compare the new value of the toggle bit with the first. If the toggle
bit is not toggling, the device has completed the program or erases operation. The system can
read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read
cycles, the system determines that the toggle bit is still toggling, the system also should note
whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then deter-
mine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just
as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed
the program or erases operation. If it is still toggling, the device did not complete the operation
successfully, and the system must write the reset command to return to reading array data. The
remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5
has not gone high. The system may continue to monitor the toggle bit and DQ5 through succes-
sive read cycles, determining the status as described in the previous paragraph. Alternatively, it
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512NC0BFWY70 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY72 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY73 | Stacked Multi-Chip Product (MCP) |
| S71WS512ND0BAWA20 | Stacked Multi-Chip Product (MCP) |
| S71WS512ND0BAWA22 | Stacked Multi-Chip Product (MCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512NC0BFWY70 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY72 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY73 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWYJ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWYJ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
發布緊急采購，3分鐘左右您將得到回復。