- 您現在的位置：買賣IC網 > PDF目錄365460 > S71WS512NC0BFWY63 (Spansion Inc.) Stacked Multi-Chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71WS512NC0BFWY63 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-Chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 36/188頁 |
| 文件大?。?/td> | 2252K |
| 代理商： | S71WS512NC0BFWY63 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁
34
S71WS-Nx0 Based MCPs
S71WS-N_01_A4 September 15, 2005
A d v a n c e I n f o r m a t i o n
10.5
Program/Erase Operations
These devices are capable of several modes of programming and or erase operations which are
described in detail in the following sections. However, prior to any programming and or erase op-
eration, devices must be setup appropriately as outlined in the configuration register
(
Table 10.8
).
For any program and or erase operations, including writing command sequences, the system
must drive AVD# and CE# to V
IL
, and OE# to V
IH
when providing an address to the device, and
drive WE# and CE# to V
IL
, and OE# to V
IH
when writing commands or programming data.
Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st
rising edge of WE# or CE#.
Note the following:
When the Embedded Program algorithm is complete, the device returns to the read mode.
The system can determine the status of the program operation by using DQ7 or DQ6. Refer
to the Write Operation Status section for information on these status bits.
A “0” cannot be programmed back to a “1.” Attempting to do so causes the device to set DQ5
= 1 (halting any further operation and requiring a reset command). A succeeding read shows
that the data is still “0.” Only erase operations can convert a “0” to a “1.”
Any commands written to the device during the Embedded Program Algorithm are ignored
except the Program Suspend command.
Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program oper-
ation is in progress.
A hardware reset immediately terminates the program operation and the program command
sequence should be reinitiated once the device has returned to the read mode, to ensure data
integrity.
Programming is allowed in any sequence and across sector boundaries for single word pro-
gramming operation.
10.5.1
Single W ord Programming
Single word programming mode is the simplest method of programming. In this mode, four Flash
command write cycles are used to program an individual Flash address. The data for this pro-
gramming operation could be 8-, 16- or 32-bits wide. While this method is supported by all
Spansion devices, in general it is not recommended for devices that support Write Buffer Pro-
gramming. See
Table 15.1
for the required bus cycles and
Figure 10.3
for the flowchart.
When the Embedded Program algorithm is complete, the device then returns to the read mode
and addresses are no longer latched. The system can determine the status of the program oper-
ation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these
status bits.
During programming, any command (except the Suspend Program command) is ignored.
The Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program op-
eration is in progress.
相關PDF資料 |
PDF描述 |
|---|---|
| S71WS512NC0BFWY70 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY72 | Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY73 | Stacked Multi-Chip Product (MCP) |
| S71WS512ND0BAWA20 | Stacked Multi-Chip Product (MCP) |
| S71WS512ND0BAWA22 | Stacked Multi-Chip Product (MCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71WS512NC0BFWY70 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY72 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWY73 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWYJ0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
| S71WS512NC0BFWYJ2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) |
發布緊急采購，3分鐘左右您將得到回復。