- 您現在的位置：買賣IC網 > PDF目錄365444 > S71PL129JA0BFI9P2 (SPANSION LLC) Stacked Multi-Chip Product (MCP) Flash Memory PDF資料下載
參數資料
| 型號： | S71PL129JA0BFI9P2 |
| 廠商： | SPANSION LLC |
| 元件分類： | 存儲器 |
| 英文描述： | Stacked Multi-Chip Product (MCP) Flash Memory |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA64 |
| 封裝： | 8 X 11.60 MM, 1.20 MM HEIGHT, LEAD FREE, FBGA-64 |
| 文件頁數： | 60/149頁 |
| 文件大小： | 2693K |
| 代理商： | S71PL129JA0BFI9P2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁
60
S29PL129J for MCP
S29PL129J_MCP_00_A0 June 4, 2004
A d v a n c e I n f o r m a t i o n
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular
sector is actively erasing (that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit II is valid after the rising
edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have
been selected for erasure. (The system may use either OE# or CE1# / CE2# to
control the read cycles.) But DQ2 cannot distinguish whether the sector is actively
erasing or is erase-suspended. DQ6, by comparison, indicates whether the device
is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors
are selected for erasure. Thus, both status bits are required for sector and mode
information. See
Table 14
to compare outputs for DQ2 and DQ6.
Figure 7
shows the toggle bit algorithm in flowchart form, and the
“DQ2: Toggle
Bit II”
explains the algorithm. See also “
DQ6: Toggle Bit I
.”
Figure 19
shows the
toggle bit timing diagram.
Figure 20
shows the differences between DQ2 and DQ6
in graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to
Figure 7
for the following discussion. Whenever the system initially be-
gins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the system would note and
store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit with the first. If the toggle
bit is not toggling, the device has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see
“DQ5: Exceeded Timing Limits”
). If it is, the system should then determine
again whether the toggle bit is toggling, since the toggle bit may have stopped
toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device
has successfully completed the program or erase operation. If it is still toggling,
the device did not completed the operation successfully, and the system must
write the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as de-
scribed in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algo-
rithm when it returns to determine the status of the operation (top of
Figure 7
).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified inter-
nal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the
program or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a
location that was previously programmed to “0.”
Only an erase operation can
Note:
The system should recheck the toggle bit even if DQ5 = “1” because the toggle
bit may stop toggling as DQ5 changes to “1.” See
“DQ6: Toggle Bit I”
and
“DQ2: Tog-
gle Bit II”
for more information.
Figure 7. Toggle Bit Algorithm
相關PDF資料 |
PDF描述 |
|---|---|
| S71PL129JC0BFW9Z0 | Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JB0BFW9Z0 | Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JA0BFW9Z0 | Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JC0BAW9Z2 | Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JB0BAW9Z2 | Stacked Multi-Chip Product (MCP) Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71PL129JA0BFI9P3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JA0BFI9U0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JA0BFI9U2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JA0BFI9U3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory |
| S71PL129JA0BFI9Z0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。