參數資料
型號： S71PL129JA0BFI9P2
廠商： SPANSION LLC
元件分類： 存儲器
英文描述： Stacked Multi-Chip Product (MCP) Flash Memory
中文描述： SPECIALTY MEMORY CIRCUIT, PBGA64
封裝： 8 X 11.60 MM, 1.20 MM HEIGHT, LEAD FREE, FBGA-64
文件頁數： 47/149頁
文件大?。?/td> 2693K
代理商： S71PL129JA0BFI9P2
June 4, 2004 S29PL129J_MCP_00_A0
S29PL129J for MCP
47
A d v a n c e I n f o r m a t i o n
Any commands written to the device during the Embedded Program Algorithm
are ignored.
Note that a
hardw are reset
immediately terminates the program
operation. The program command sequence should be reinitiated once that bank
has returned to the read mode, to ensure data integrity. Note that the Secured
Silicon Sector, autoselect and CFI functions are unavailable when the Secured Sil-
icon Sector is enabled.
Programming is allowed in any sequence and across sector boundaries.
A bit
cannot be programmed from “ 0” back to a “ 1.”
Attempting to do so may
cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate
the operation was successful. However, a succeeding read shows that the data is
still “0.” Only erase operations can convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program data to a bank faster
than using the standard program command sequence. The unlock bypass com-
mand sequence is initiated by first writing two unlock cycles. This is followed by
a third write cycle containing the unlock bypass command, 20h. That bank then
enters the unlock bypass mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The first cycle in this se-
quence contains the unlock bypass program command, A0h; the second cycle
contains the program address and data. Additional data is programmed in the
same manner. This mode dispenses with the initial two unlock cycles required in
the standard program command sequence, resulting in faster total programming
time.
Table 12
shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (
Table 13
)
The device offers accelerated program operations through the WP#/ACC pin.
When the system asserts V
HH
on the WP#/ACC pin, the device automatically en-
ters the Unlock Bypass mode. The system may then write the two-cycle Unlock
Bypass program command sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation.
Note that the WP#/ACC pin must not
be at V
HH
any operation other than accelerated programming, or device damage
may result. In addition, the WP#/ACC pin must not be left floating or uncon-
nected; inconsistent behavior of the device may result.
Figure 4
illustrates the algorithm for the program operation. See the
Erase/Pro-
gram Operations
table in
AC Characteristics
for parameters, and
Figure 14
for
timing diagrams.
相關PDF資料
PDF描述
S71PL129JC0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JB0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JC0BAW9Z2 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JB0BAW9Z2 Stacked Multi-Chip Product (MCP) Flash Memory
相關代理商/技術參數
參數描述
S71PL129JA0BFI9P3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9Z0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*