參數資料
型號： S71PL129JA0BFI9P2
廠商： SPANSION LLC
元件分類： 存儲器
英文描述： Stacked Multi-Chip Product (MCP) Flash Memory
中文描述： SPECIALTY MEMORY CIRCUIT, PBGA64
封裝： 8 X 11.60 MM, 1.20 MM HEIGHT, LEAD FREE, FBGA-64
文件頁數： 19/149頁
文件大?。?/td> 2693K
代理商： S71PL129JA0BFI9P2
June 4, 2004 S29PL129J_MCP_00_A0
S29PL129J for MCP
19
A d v a n c e I n f o r m a t i o n
Device Bus Operations
This section describes the requirements and use of the device bus operations,
which are initiated through the internal command register. The command register
itself does not occupy any addressable memory location. The register is a latch
used to store the commands, along with the address and data information
needed to execute the command. The contents of the register serve as inputs to
the internal state machine. The state machine outputs dictate the function of the
device.
Table 1
lists the device bus operations, the inputs and control levels re-
quired, and the resulting output. The following subsections describe each of these
operations in further detail.
Legend:
L = Logic Low = V
IL
, H = Logic High = V
IH
, V
ID
= 11.5–12.5
V, V
HH
= 8.5–9.5
V, X = Don’t Care, SA = Sector
Address, A
IN
= Address In, D
IN
= Data In, D
OUT
= Data Out
Notes:
1. The sector protect and sector unprotect functions may also be implemented via programming equipment. See
“
“High Voltage Sector Protection”
on page 37.”
2. WP#/ACC must be high when writing to upper two and lower two sectors.
Requirements for Reading Array Data
To read array data from the outputs, the system must drive the OE# and appro-
priate CE# pins to V
IL
. In PL129J, CE1# and CE2# are the power control and
select the lower (CE1#) or upper (CE2#) halves of the device. CE# is the power
control. OE# is the output control and gates array data to the output pins. WE#
should remain at V
IH
.
The internal state machine is set for reading array data upon device power-up,
or after a hardware reset. This ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this
mode to obtain array data. Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid data on the device data
outputs. Each bank remains enabled for read access until the command register
contents are altered.
See
Table 24
for timing specifications and
Figure 11
for the timing diagram. I
CC1
in the DC Characteristics table represents the active current specification for
reading array data.
Table 1. PL129J Device Bus Operations
Operation
CE1#
CE2#
OE#
WE#
RESET#
WP#/ACC
Addresses
(A21–A0)
DQ15–
DQ0
Read
L
H
L
H
H
X
A
IN
D
OUT
H
L
Write
L
H
H
L
H
X
(
Note 2
)
A
IN
D
IN
H
L
Standby
V
IO
±
0.3 V
V
IO
±
0.3 V
X
X
V
IO
±
0.3 V
X
X
High-Z
Output Disable
L
L
H
H
H
X
X
High-Z
Reset
X
X
X
X
L
X
X
High-Z
Temporary Sector Unprotect
(High Voltage)
X
X
X
X
V
ID
X
A
IN
D
IN
相關PDF資料
PDF描述
S71PL129JC0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JB0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFW9Z0 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JC0BAW9Z2 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JB0BAW9Z2 Stacked Multi-Chip Product (MCP) Flash Memory
相關代理商/技術參數
參數描述
S71PL129JA0BFI9P3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9U3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129JA0BFI9Z0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*