- 您現在的位置：買賣IC網 > PDF目錄374668 > S5935QF (APPLIEDMICRO INC) PCI 5V Bus Master/Target Device 32-bit PDF資料下載
參數資料
| 型號： | S5935QF |
| 廠商： | APPLIEDMICRO INC |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI 5V Bus Master/Target Device 32-bit |
| 中文描述： | PCI BUS CONTROLLER, PQFP160 |
| 封裝： | PLASTIC, QFP-160 |
| 文件頁數： | 118/190頁 |
| 文件大?。?/td> | 748K |
| 代理商： | S5935QF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁當前第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁
9-110
MAILBOX OVERVIEW
S5935
Mailbox Empty/Full Conditions
The PCI and Add-On interfaces each have a mailbox
status register. The PCI Mailbox Empty/Full Status
(MBEF) and Add-On Mailbox Empty/Full Status
(AMBEF) Registers indicate the status of all bytes
within the mailbox registers. A write to an outgoing
mailbox sets the status bits for that mailbox. The byte
enables determine which bytes within the mailbox be-
come full (and which status bits are set).
An outgoing mailbox for one interface is an incoming
mailbox for the other. Therefore, incoming mailbox
status bits on one interface are identical to the corre-
sponding outgoing mailbox status bits on the other
interface. The following list shows the relationship be-
tween the mailbox registers on the PCI and Add-On
interfaces.
PCI Interface
Add-On Interface
Outgoing Mailbox 1
Outgoing Mailbox 2
Outgoing Mailbox 3
Outgoing Mailbox 4
Incoming Mailbox 1
Incoming Mailbox 2
Incoming Mailbox 3
Incoming Mailbox 4
PCI Mailbox Empty/Full = Add-On Mailbox Empty/Full
= Incoming Mailbox 1
= Incoming Mailbox 2
= Incoming Mailbox 3
= Incoming Mailbox 4
= Outgoing Mailbox 1
= Outgoing Mailbox 2
= Outgoing Mailbox 3
= Outgoing Mailbox 4
A write to an outgoing mailbox also writes data into
the incoming mailbox on the other interface. It also
sets the status bits for the outgoing mailbox and the
status bits for the incoming mailbox on the other in-
terface. Reading the incoming mailbox clears all cor-
responding status bits in the Add-On and PCI
mailbox status registers (AMBEF and MBEF).
For example, a PCI write is performed to the PCI out-
going mailbox 2, writing bytes 0 and 1 (BE0# and
BE1# asserted). Reading the PCI Mailbox Empty/Full
Status Register (MBEF) indicates that bits 4 and 5 are
set. These bits indicate that outgoing mailbox 2, bytes
0 and 1 are full. Reading the Add-On Mailbox Empty/
Full Status Register (AMBEF) shows that bits 4 and 5
in this register are also set, indicating Add-On incom-
ing mailbox 2, bytes 0 and 1 are full. An Add-On read
of incoming mailbox 2, bytes 0 and 1 clears the status
bits in both the MBEF and AMBEF status registers.
To reset individual flags in the MBEF and AMBEF
registers, the corresponding byte must be read from
the incoming mailbox. The PCI and Add-On mailbox
status registers, MBEF and AMBEF, are read-only.
Mailbox flags may be globally reset from either the
PCI interface or the Add-On interface. The PCI Bus
Master Control/Status Register (MCSR) and the Add-
On General Control/Status Register (AGCSTS) each
have a bit to reset all of the mailbox status flags.
Mailbox Interrupts
The designer has the option to generate interrupts to
the PCI and Add-On interfaces when specific mailbox
events occur. The PCI and Add-On interfaces can
each define two conditions where interrupts may be
generated. An interrupt can be generated when an
incoming mailbox becomes full and/or when an outgo-
ing mailbox becomes empty. A specific byte within a
specific mailbox is selected to generate the interrupt.
The conditions defined to generate interrupts to the
PCI interface do not have to be the same as the condi-
tions defined for the Add-On interface. Interrupts are
cleared through software.
For incoming mailbox interrupts, when the specified
byte becomes full, an interrupt is generated. The in-
terrupt might be used to indicate command or status
information has been provided, and must be read.
For PCI incoming mailbox interrupts, the S5935 as-
serts the PCI interrupt, INTA#. For Add-On incoming
mailbox interrupts, the S5935 asserts the Add-On in-
terrupt, IRQ#.
For outgoing mailbox interrupts, when the specified
byte becomes empty, an interrupt is generated. The
interrupt might be used to indicate that the other in-
terface has received the last information sent and
more may be written. For PCI outgoing mailbox inter-
rupts, the S5935 asserts the PCI interrupt, INTA#.
For Add-On outgoing mailbox interrupts, the S5935
asserts the Add-On interrupt, IRQ#.
Add-On Outgoing Mailbox 4, Byte 3 Access
PCI incoming mailbox 4, byte 3 (Add-On outgoing
mailbox 4, byte 3) does not function exactly like the
other mailbox bytes. When an a serial nv memory
boot device or no external boot device is used, the
S5935 pins EA7:0 are redefined to provide direct ex-
ternal access to Add-On outgoing mailbox 4, byte 3.
EA8 is redefined to provide a load clock which may
be used to generate a PCI interrupt. The pins are
redefined as follows:
Signal Pin
Add-On Outgoing Mailbox
EA0/EMB0
EA1/EMB1
EA2/EMB2
EA3/EMB3
EA4/EMB4
EA5/EMB5
EA6/EMB6
EA7/EMB7
EA8/EMBCLK
Mailbox 4, bit 24
Mailbox 4, bit 25
Mailbox 4, bit 26
Mailbox 4, bit 27
Mailbox 4, bit 28
Mailbox 4, bit 29
Mailbox 4, bit 30
Mailbox 4, bit 31
Mailbox 4, byte 3 load clock
相關PDF資料 |
PDF描述 |
|---|---|
| S5990-01 | POSITION SENSITIVE DETECTOR |
| S5629-01 | POSITION SENSITIVE DETECTOR |
| S5629-02 | POSITION SENSITIVE DETECTOR |
| S5991-01 | POSITION SENSITIVE DETECTOR |
| S5629 | POSITION SENSITIVE DETECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5935QRC | 制造商:AppliedMicro 功能描述:PCI Master Device 160-Pin PQFP |
| S5935TF | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI 5V Bus Master/Target Device 32-bit |
| S5935TFC | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI Product |
| S593T | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:MOSMIC for TV-Tuner Prestage with 5 V Supply Voltage |
| S593T_08 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:MOSMIC? for TV-Tuner Prestage with 5 V Supply Voltage |
發布緊急采購，3分鐘左右您將得到回復。