參數資料
型號： S29GL01GP13FAI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
中文描述： 1G X 1 FLASH 3V PROM, 130 ns, PBGA64
封裝： 13 X 11 MM, 1 MM PITCH, FBGA-64
文件頁數： 38/71頁
文件大?。?/td> 990K
代理商： S29GL01GP13FAI010
36
S29GL-P MirrorBit
TM
Flash Family
S29GL-P_00_A3 November21,2006
D a t a
S h e e t
( A d v a n c e
I n f o r m a t i o n )
Note
Hardware reset operation during embedded erase is not recommended; permanent device damage may
result.
7.9.3
Software Reset
Software reset is part of the command set (see
Table 12.1 on page 61
) that also returns the device to array
read mode and must be used for the following conditions:
1. to exit Autoselect mode
2. when DQ5 goes high during write status operation that indicates program or erase cycle was not
successfully completed
3. exit sector lock/unlock operation.
4. to return to erase-suspend-read mode if the device was previously in Erase Suspend mode.
5. after any aborted operations
Software Functions and Sample Code
Note
Base = Base Address.
The following is a C source code example of using the reset function. Refer to the
Spansion Low Level Driver
User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash memory software
development guidelines.
/* Example: Reset (software reset of Flash state machine) */
*( (UINT16 *)base_addr + 0x000 ) = 0x00F0;
The following are additional points to consider when using the reset command:
This command resets the sectors to the read and address bits are ignored.
Reset commands are ignored once erasure has begun until the operation is complete.
Once programming begins, the device ignores reset commands until the operation is complete
The reset command may be written between the cycles in a program command sequence before
programming begins (prior to the third cycle). This resets the sector to which the system was writing to the
read mode.
If the program command sequence is written to a sector that is in the Erase Suspend mode, writing the
reset command returns that sector to the erase-suspend-read mode.
The reset command may be also written during an Autoselect command sequence.
If a sector has entered the Autoselect mode while in the Erase Suspend mode, writing the reset command
returns that sector to the erase-suspend-read mode.
If DQ1 goes high during a Write Buffer Programming operation, the system must write the "Write to Buffer
Abort Reset" command sequence to RESET the device to reading array data. The standard RESET
command does not work during this condition.
To exit the unlock bypass mode, the system must issue a two-cycle unlock bypass reset command
sequence [see command table for details].
Table 7.18
Reset
(LLD Function = lld_ResetCmd)
Cycle
Operation
Byte Address
Word Address
Data
Reset Command
Write
Base + xxxh
Base + xxxh
00F0h
相關PDF資料
PDF描述
S29GL01GP13FAI012 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI013 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI020 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI022 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI023 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
相關代理商/技術參數
參數描述
S29GL01GP13FAI012 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI020 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI022 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
S29GL01GP13FAI023 制造商:SPANSION 制造商全稱:SPANSION 功能描述:3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*