參數資料
型號： S1C88816D
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC164
封裝： DIE-164
文件頁數： 42/173頁
文件大?。?/td> 1411K
代理商： S1C88816D
128
EPSON
S1C88816 TECHNICAL MANUAL
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (A/D Converter)
5.15.7 Programming notes
(1) When the OSC3 oscillation circuit is made the
clock source, it is necessary to turn the OSC3
oscillation ON, prior to using the A/D con-
verter.
From the time the OSC3 oscillation circuit is
turning ON until oscillation stabilizes, an
interval of several msec to several 10 msec is
necessary. Consequently, you should allow an
adequate waiting time after turning the OSC3
oscillation circuit ON before starting the count
of the programmable timer. (The oscillation
start time will vary somewhat depending on the
oscillator and on external parts. Refer to the
oscillation start time example indicated in
Chapter 7, "ELECTRICAL CHARACTERIS-
TICS".)
At initial reset, OSC3 oscillation circuit is set to
OFF status.
(2) When SLEEP mode is set during A/D conver-
sion, correct A/D conversion result cannot be
obtained because the OSC3 oscillation circuit
stops. Do not set in SLEEP mode during A/D
conversion.
(3) The input clock and analog input terminals
should be set when the A/D converter stops.
Changing in the A/D converter operation may
cause a malfunction.
(4) The frequency of the input clock should be
lower than the maximum value shown in
Section 7.8, "A/D Converter Characteristics".
(5) To prevent malfunction, do not start A/D
conversion (writing to the CHS register) when
the A/D conversion clock is not being input to
the A/D converter, and do not turn the clock off
during A/D conversion.
(6) If the CHS register selects an input channel
which is not included in the analog input
terminals set by the PAD register (the PAD
register can select several terminals simulta-
neously), the A/D conversion does not result in
a correct converted value.
(7) During A/D conversion, do not operate the P1n
terminals which are not used for analog inputs
of the A/D converter (for input/output of
digital signal etc.). It affects the A/D conversion
precision.
相關PDF資料
PDF描述
S1C88832F0A0100 MICROCONTROLLER, PQFP128
S1C88848D0A0100 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
相關代理商/技術參數
參數描述
S1C88848 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*