參數資料
型號: S1C88816D
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC164
封裝: DIE-164
文件頁數: 12/173頁
文件大小: 1411K
代理商: S1C88816D
S1C88816 TECHNICAL MANUAL
EPSON
101
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (LCD Controller)
5.11.6 Display control
The display status of the built-in LCD driver and
the contrast adjustment can be controlled with the
built-in LCD controller. The LCD display status can
be selected by display control registers LCDC0 and
LCDC1. Setting the value and display status are
shown in Table 5.11.6.1.
Table 5.11.6.1 LCD display control
All the dots in the LCD display can be turned on or
off directly by the drive waveform output from the
LCD driver, and data in the display memory is not
changed. Also, since the common terminal at this
time is set to static drive when all the dots are on
and is set to dynamic drive when they are off, this
function can be used as follows:
(1) Since all dots on is binary output (VC5 and VSS)
with static drive, the common/segment termi-
nal can be used as a monitor terminal for the
OSC1 oscillation frequency adjustment.
(2) Since all dots off is dynamic drive, you can
brink the entire LCD display without changing
display memory data.
LCDC1
LCDC0
LCD display
1
0
1
0
1
0
All LCDs lit (Static)
All LCDs out (Dynamic)
Normal display
Drive OFF
LC3
LC0
Contrast
1
:
0
1
0
1
:
0
1
0
Dark
Light
LC1
1
0
:
1
0
LC2
1
:
0
Selecting LCD drive OFF turns the LCD drive
power circuit OFF and all the VC1–VC5 terminals go
to VSS level. If external power supply has been
selected by the mask option, the VC1–VC5 shift to
floating status to prevent shortcircuit between the
external power supply and the internal power
supply. However, do not set LCDC0 and LCDC1 to
"0" even when an external power supply is used.
Furthermore, when the SLP instruction is executed,
registers LCDC0 and LCDC1 are automatically
reset to "0" (set to drive off) by hardware.
The LCD contrast can be adjusted in 16 stages. This
adjustment is done by the contrast adjustment
register LC0–LC3, and the setting values corre-
spond to the contrast as shown in Table 5.11.6.2.
However, if external power supply has been
selected by the mask option, the contrast adjust-
ment register LC0–LC3 is ineffective and contrast
adjustment cannot be done.
Table 5.11.6.2 LCD contrast adjustment
相關PDF資料
PDF描述
S1C88832F0A0100 MICROCONTROLLER, PQFP128
S1C88848D0A0100 8-BIT, MROM, 8.2 MHz, MICROCONTROLLER, UUC192
S1C8F360F 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP176
S1D13305F00B 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
S1D13305F00A 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
相關代理商/技術參數
參數描述
S1C88848 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C8F360D411000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360D511000 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F413100 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
S1C8F360F513200 功能描述:16位微控制器 - MCU 8-bit Flash 60KB LCD Dr. 51 x 32 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT