Advance Information
PowerNP
TM
NPe405H Embedded Processor Data Sheet
60
[HDLCMPTxData4:7]
[HDLCMPTxEn0:7]
HDLCMPRxClk0:3
[HDLCMPRxClk4:7]
HDLCMPRxData0:3
[HDLCMPRxData4:7]
Internal Peripheral Interface
IICSCL
IICSDA
[UART0_CTS]CGPIO26
[UART0_DCD]CGPIO28
[UART0_DSR]CGPIO27
[UART0_DTR]CGPIO31
[UART0_RI][CGPIO29]
[UART0_RTS]CGPIO30
UART0_Rx
UART0_Tx
[UART1_CTS]CGPIO20
[UART1_DCD]CGPIO22
[UART1_DSR]CGPIO21
[UART1_DTR]CGPIO25
[UART1_RI]CGPIO23
[UART1_RTS]CGPIO24
UART1_Rx
UART1_Tx
UARTSerClk
Interrupts Interface
[IRQ0:6]SGPIO17:23
JTAG Interface
TCK
TDI
TDO
TMS
TRST
12
12
n/a
n/a
n/a
n/a
8
8
n/a
n/a
n/a
n/a
async
async
async
async
async
n/a
async
n/a
async
n/a
async
async
async
n/a
async
n/a
async
n/a
async
async
async
async
async
async
n/a
async
n/a
async
n/a
async
async
async
n/a
async
n/a
async
n/a
async
async
async
n/a
n/a
n/a
async
n/a
async
n/a
async
n/a
n/a
n/a
async
n/a
async
n/a
async
n/a
async
async
n/a
n/a
n/a
async
n/a
async
n/a
async
n/a
n/a
n/a
async
n/a
async
n/a
async
n/a
17
17
n/a
n/a
n/a
12
n/a
12
n/a
12
n/a
n/a
n/a
12
n/a
12
n/a
12
n/a
11
11
n/a
n/a
n/a
8
n/a
8
n/a
8
n/a
n/a
n/a
8
n/a
8
n/a
8
n/a
async
async
n/a
n/a
n/a
n/a
async
async
n/a
async
async
async
async
n/a
async
async
n/a
n/a
async
n/a
n/a
n/a
n/a
async
n/a
n/a
n/a
n/a
12
n/a
n/a
n/a
n/a
8
n/a
n/a
I/O Specifications—266MHz
(Part 3 of 5)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2.
The two-cycle SDRAM command interface is driven in cycle 1 and used in cycle 2. Output times in table are in cycle 1.
3.
SDRAM output timing is relative to the rising edge of the internal PLB clock, which is an integral multiple of and rising-
edge aligned with SysClk. Therefore, SDRAM output timings in the table are shown relative to SysClk. Timings shown
are for a lumped 50pF load, however the interface has been verified for PC100-compliant operation using transmission
line circuit analysis.
4. SDRAM MemClkOut0:1 rising edge at package pin precedes the internal PLB clock by approximately 0.5ns for a
typical clock network or a lumped 10pF load.
5. PerClk rising edge at package pin with a 10pF load trails the internal PLB clock by approximately 0.8ns.
6.
PCI timings are for asynchronous operation up to 66MHz. PCI output hold time requirement is 1ns for 66MHz and 2ns
for 33MHz.
Signal
Input (ns)
Output (ns)
Output Current (mA)
Clock
Notes
Setup Time
(minimum)
Hold Time
(minimum)
Valid Delay
(maximum)
50pF load
Hold Time
(minimum)
50pF load
I/O H
(maximum)
I/O L
(minimum)