參數資料
型號： PCA9665
廠商： NXP Semiconductors N.V.
英文描述： Fm+ parallel bus to I2C-bus controller
中文描述： 調頻并行總線I2C總線控制器
文件頁數： 60/91頁
文件大?。?/td> 372K
代理商： PCA9665
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
60 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
8.9.5
Bus error
A bus error occurs when a START or STOP condition is present at an illegal position in the
format frame. Examples of illegal positions are during the serial transfer of an address
byte, a data or an acknowledge bit.
The PCA9665 only reacts to a bus error when it is involved in a serial transfer either as a
master or an addressed slave. When a bus error is detected, PCA9665 releases the SDA
and SCL lines, sets the interrupt flag, and loads the status register with 00h. This status
code may be used to vector to a service routine which either attempts the aborted serial
transfer again or simply recovers from the error condition as shown in
Table 46
“Miscellaneous states”
. The microcontroller must send an external hardware or software
reset signal to reset the PCA9665.
8.10 Power-on reset
When power is applied to V
DD
, an internal Power-On Reset holds the PCA9665 in a reset
condition until V
DD
has reached V
POR
. At this point, the reset condition is released and the
PCA9665 goes to the power-up initialization phase where the following operations are
performed:
1. ENSIO bit is set to 1 to enable the internal oscillator.
2. Internal register initialization is performed.
3. ENSIO bit is set to 0 to disable the internal oscillator and go to the non-addressed low
power mode.
The complete power-up initialization phase takes 550
μ
s to be performed. During this
time, write to the PCA9665 through the parallel port is not permitted. However, the parallel
port can be read. This allows the device connected to the parallel port of the PCA9665 to
poll the I2CCON register and read the ENSIO state bit. When ENSIO bit is equal to 1, this
means that the power-up initialization is in progress. When ENSIO is set to 0, this means
that the power-up initialization is done and that the PCA9665 is initialized and ready to be
used.
Fig 17. Recovering from a bus obstruction caused by a LOW level on SDA
1
2
3
4
5
6
7
8
9
002aab030
STOP
condition
START
condition
STA flag
SDA line
SCL line
相關PDF資料
PDF描述
PCA9665N Fm+ parallel bus to I2C-bus controller
PCA9671 Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9665APW,118 功能描述:I2C 接口集成電路 Fm+ parallel bus I2C bus controller RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS,118 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS-T 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*