參數資料
型號： PCA9665
廠商： NXP Semiconductors N.V.
英文描述： Fm+ parallel bus to I2C-bus controller
中文描述： 調頻并行總線I2C總線控制器
文件頁數： 36/91頁
文件大?。?/td> 372K
代理商： PCA9665
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
36 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
8.4.2
Master Receiver Buffered mode
In the Master Receiver Buffered mode, a number of data bytes are received from a slave
transmitter several bytes at a time (see
Figure 12
). The transfer is initialized as in the
Master Transmitter Byte mode.
The Master Receiver Buffered mode may now be entered by setting the STA bit. The
I
2
C-bus state machine will first test the I
2
C-bus and generate a START condition as soon
as the bus becomes free. When a START condition is transmitted, the Serial Interrupt flag
(SI) is set, the Interrupt line (INT) goes LOW and the status code in the status register
(I2CSTA) will be 08h. This status code must be used to vector to an interrupt service
routine that loads I2CDAT with the slave address and the data direction bit (SLA+R). The
byte count register (I2CCOUNT) needs to be programmed with the number of bytes that
need to be received in a single sequence (BC[6:0]). LB bit is programmed with logic 0 if
the last received byte needs to be acknowledged (read operation still ongoing) or with
logic 1 if the last received byte needs to be not acknowledged (read operation ends so the
PCA9665 can issue a STOP or Re-START condition). A write to I2CCON resets the SI bit,
clears the Interrupt (INT goes HIGH) and allows the serial transfer to continue.
When the slave address and the data direction bit have been transmitted and all the data
bytes have been received, the Serial Interrupt flag (SI) is set again, the Interrupt line (INT)
goes LOW again and I2CSTA is loaded with the following possible codes:
48h if a no acknowledgment bit (NACK) has been received for the slave address with
direction bit
50h when all the bytes have been received and an acknowledgement bit (ACK) has
been returned for all the bytes
58h when all the bytes have been received and an acknowledgement bit (ACK) has
been returned for all the bytes except the last one
38h if the PCA9665 lost the arbitration
B0h if the PCA9665 lost the arbitration and is addressed as a slave transmitter (slave
mode enabled with AA = 1)
68h if the PCA9665 lost the arbitration and is addressed as a slave receiver (slave
mode enabled with AA = 1)
D8h if the PCA9665 lost the arbitration and is addressed as a slave receiver during a
General Call sequence (slave mode enabled with AA = 1 and General Call address
enabled with GC = 1 in I2CADR register).
The appropriate action to be taken for each of these status codes is detailed in
Table 36
.
ENSIO is not affected by the serial transfer and is not referred to in
Table 36
.
After a repeated START condition (state 10h), the PCA9665 may switch to the Master
Transmitter mode by loading I2CDAT with SLA+W.
Remark:
A master should not transmit its own slave address.
相關PDF資料
PDF描述
PCA9665N Fm+ parallel bus to I2C-bus controller
PCA9671 Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9665APW,118 功能描述:I2C 接口集成電路 Fm+ parallel bus I2C bus controller RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS,118 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS-T 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*