參數資料
型號： PCA9665
廠商： NXP Semiconductors N.V.
英文描述： Fm+ parallel bus to I2C-bus controller
中文描述： 調頻并行總線I2C總線控制器
文件頁數： 11/91頁
文件大?。?/td> 372K
代理商： PCA9665
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
11 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
Remark:
ENSIO bit value must be changed only when the I
2
C-bus is idle.
7.3.1.5
The indirect data field access register, INDIRECT (A1 = 1, A0 = 0)
The registers in the indirect address space can be accessed using the INDIRECT data
field. Before writing or reading such a register, the INDPTR register should be written with
the address of the indirect register that needs to be accessed. Once the INDPTR register
contains the appropriate value, reads and writes to the INDIRECT data field will actually
read and write the selected indirect register.
5
STA
The START flag.
STA = 1: When the STA bit is set to enter a master mode, the bus controller
hardware checks the status of the I
2
C-bus and generates a START condition if the
bus is free. If the bus is not free, then the bus controller waits for a STOP condition
(which will free the bus) and generates a START condition after the minimum
buffer time (t
BUF
) has elapsed.
If STA is set while the bus controller is already in a master mode and one or more
bytes are transmitted or received, the bus controller transmits a repeated START
condition. STA may be set at any time. STA may also be set when the bus
controller is an addressed slave. A START condition will then be generated after a
STOP condition and the minimum buffer time (t
BUF
) has elapsed.
STA = 0: When the STA bit is reset, no START condition or repeated START
condition will be generated.
The STOP flag.
STO = 1: When the STO bit is set while the bus controller is in a master mode, a
STOP condition is transmitted on the I
2
C-bus. When a STOP condition is detected
on the bus, the hardware clears the STO flag.
If the STA and STO bits are both set, then a STOP condition is transmitted on the
I
2
C-bus, if the PCA9665 is in a master mode. the bus controller then transmits a
START condition after the minimum buffer time (t
BUF
) has elapsed.
STO = 0 : When the STO bit is reset, no STOP condition will be generated.
The Serial Interrupt flag.
SI = 1: When the SI flag is set, and, if the ENSIO bit is also set, a serial interrupt is
requested. SI is set by hardware when one of 29 of the 30 possible states of the
bus controller states is entered. The only state that does not cause SI to be set is
state F8h, which indicates that no relevant state information is available.
While SI is set, the LOW period of the serial clock on the SCL line is stretched,
and the serial transfer is suspended. A HIGH level on the SCL line is unaffected
by the serial interrupt flag. SI is automatically cleared when the I2CCON register
is written. The SI bit cannot be set by the user.
SI = 0: When the SI flag is reset, no serial interrupt is requested, and there is no
stretching of the serial clock on the SCL line.
Reserved. When I2CCON is read, zeroes are read. Must be written with zeroes.
The Mode flag.
MODE = 0; Byte mode. See
Section 8.1.1 “Byte mode”
for more detail.
MODE = 1; buffered mode. See
Section 8.1.2 “Buffered mode”
for more detail.
4
STO
3
SI
2:1
0
-
MODE
Table 12.
Bit
I2CCON - Control register (A1 = 1, A0 = 1) bit description
…continued
Symbol Description
相關PDF資料
PDF描述
PCA9665N Fm+ parallel bus to I2C-bus controller
PCA9671 Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9665APW,118 功能描述:I2C 接口集成電路 Fm+ parallel bus I2C bus controller RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS,118 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS-T 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*